參數資料
型號: TSXPC603RVGB/Q14LC
廠商: ATMEL CORP
元件分類: 微控制器/微處理器
英文描述: 32-BIT, 300 MHz, RISC PROCESSOR, CBGA255
封裝: 21 X 21 MM, 3 MM HEIGHT, 1.27 MM PITCH, CERAMIC, BGA-255
文件頁數: 45/83頁
文件大?。?/td> 8336K
代理商: TSXPC603RVGB/Q14LC
41
8021G–AVR–03/11
ATmega329P/3290P
9.10.6
Port Pins
When entering a sleep mode, all port pins should be configured to use minimum power. The
most important is then to ensure that no pins drive resistive loads. In sleep modes where both
the I/O clock (clk
I/O) and the ADC clock (clkADC) are stopped, the input buffers of the device will
be disabled. This ensures that no power is consumed by the input logic when not needed. In
some cases, the input logic is needed for detecting wake-up conditions, and it will then be
enabled. Refer to the section ”Digital Input Enable and Sleep Modes” on page 67 for details on
which pins are enabled. If the input buffer is enabled and the input signal is left floating or have
an analog signal level close to V
CC/2, the input buffer will use excessive power.
For analog input pins, the digital input buffer should be disabled at all times. An analog signal
level close to V
CC/2 on an input pin can cause significant current even in active mode. Digital
input buffers can be disabled by writing to the Digital Input Disable Registers (DIDR1 and
9.10.7
JTAG Interface and On-chip Debug System
If the On-chip debug system is enabled by the OCDEN Fuse and the chip enter Power down or
Power save sleep mode, the main clock source remains enabled. In these sleep modes, this will
contribute significantly to the total current consumption. There are three alternative ways to
avoid this:
Disable OCDEN Fuse.
Disable JTAGEN Fuse.
Write one to the JTD bit in MCUCR.
The TDO pin is left floating when the JTAG interface is enabled while the JTAG TAP controller is
not shifting data. If the hardware connected to the TDO pin does not pull up the logic level,
power consumption will increase. Note that the TDI pin for the next device in the scan chain con-
tains a pull-up that avoids this problem. Writing the JTD bit in the MCUCR register to one or
leaving the JTAG fuse unprogrammed disables the JTAG interface.
相關PDF資料
PDF描述
TS80C31X2-LJER 8-BIT, 30 MHz, MICROCONTROLLER, PQFP44
TS80C32X2-ELCR 8-BIT, MICROCONTROLLER, PQFP44
TS80C31X2-VJBB 8-BIT, 40 MHz, MICROCONTROLLER, PQCC44
TSC80C31-16KAD 8-BIT, 16 MHz, MICROCONTROLLER, PDIP40
TSC80C31-40JDB 8-BIT, 40 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
TSXPC860SRVZQU66D 功能描述:IC MPU POWERQUICC 66MHZ 357PBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:60 系列:SCC 處理器類型:Z380 特點:全靜電 Z380 CPU 速度:20MHz 電壓:5V 安裝類型:表面貼裝 封裝/外殼:144-LQFP 供應商設備封裝:144-LQFP 包裝:托盤
TSXPCX1031 制造商:Schneider Electric 功能描述:CABLE TO PC SERIAL PORT (SUB-D9) 制造商:Schneider Electric 功能描述:PROGRAMMABLE CABLE 制造商:Schneider Electric 功能描述:MULTI-FUNCTION COMMUNICATION CABLE 制造商:Schneider Electric 功能描述:PROGRAMMABLE CABLE; Accessory Type:Programmable Cable; For Use With:Schneider Non-Ethernet Based Twido PLCs ;RoHS Compliant: Yes 制造商:Schneider Electric 功能描述:Programme cable for twido-nano-micro PLC
TSXPLP01 制造商:Schneider Electric 功能描述:BATTERY FOR TSX 37 制造商:Schneider Electric 功能描述:BATTERY FOR TSX 37 ;ROHS COMPLIANT: YES 制造商:Schneider Electric 功能描述:TSXPLP01 PLC replacement battery
TSXPLP101 制造商:Schneider Electric 功能描述:BATTERY TSX 37 QTY.10, TSXPLP101
TSXPRGLDR 制造商:Schneider Electric 功能描述:PROGRAM LOADER FOR 07/37