- 您現在的位置：買賣IC網 > PDF目錄376448 > X9520B20IB (Intersil Corporation) Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors PDF資料下載
參數資料
| 型號： | X9520B20IB |
| 廠商： | Intersil Corporation |
| 英文描述： | Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors |
| 中文描述： | 三氯酚，葡萄牙，2kbit EEPROM存儲器，雙電壓監視器 |
| 文件頁數： | 4/33頁 |
| 文件大?。?/td> | 561K |
| 代理商： | X9520B20IB |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
4
FN8206.0
March 8, 2005
PRINCIPLES OF OPERATION
SERIAL INTERFACE
Serial Interface Conventions
The device supports a bidirectional bus oriented protocol.
The protocol defines any device that sends data onto the
bus as a transmitter, and the receiving device as the
receiver. The device controlling the transfer is called the
master and the device being controlled is called the
slave. The master always initiates data transfers, and
provides the clock for both transmit and receive opera-
tions. Therefore, the X9520 operates as a slave in all
applications.
Serial Clock and Data
Data states on the SDA line can change only while SCL
is LOW. SDA state changes while SCL is HIGH are
reserved for indicating START and STOP conditions.
See Figure 1. On power-up of the X9520, the SDA pin is
in the input mode.
Serial Start Condition
All commands are preceded by the START condition,
which is a HIGH to LOW transition of SDA while SCL is
HIGH. The device continuously monitors the SDA and
SCL lines for the START condition and does not respond
to any command until this condition has been met. See
Figure 2.
Serial Stop Condition
All communications must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA
while SCL is HIGH. The STOP condition is also used to
place the device into the Standby power mode after a
read sequence. A STOP condition can only be issued
after the transmitting device has released the bus. See
Figure 2.
Serial Acknowledge
An ACKNOWLE DGE (ACK) is a software convention
used to indicate a successful data transfer. The trans-
mitting device, either master or slave, will release the
bus after transmitting eight bits. During the ninth clock
cycle, the receiver will pull the SDA line LOW to
ACKNOWLEDGE that it received the eight bits of data.
Refer to Figure 3.
The device will respond with an ACKNOWLEDGE after
recognition of a START condition if the correct Device
Identifier bits are contained in the Slave Address Byte. If
a write operation is selected, the device will respond with
an ACKNOWLEDGE after the receipt of each subse-
quent eight bit word.
In the read mode, the device will transmit eight bits of
data, release the SDA line, then monitor the line for an
ACKNOWLEDGE. If an ACKNOWLEDGE is detected
and no STOP condition is generated by the master, the
device will continue to transmit data. The device will ter-
SCL
SDA
Data Stable
Data Change
Data Stable
Figure 1.
Valid Data Changes on the SDA Bus
SCL
SDA
Start
Stop
Figure 2.
Valid Start and Stop Conditions
X9520
相關PDF資料 |
PDF描述 |
|---|---|
| X9520 | Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors |
| X9520V20IA | Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors |
| X9520V20IB | Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors |
| X9522 | Laser Diode Control for Fiber Optic Modules |
| X9522B20I-A | Laser Diode Control for Fiber Optic Modules |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9520B20I-B | 制造商:Intersil Corporation 功能描述:TRIPLE DCP POR EEPROM MEMORY 20CSP - Rail/Tube |
| X9520B20I-BT1 | 功能描述:IC LASR CTRLR 3CHAN 5.5V 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9520CZ6 WAF | 制造商:Intersil Corporation 功能描述: |
| X9520V20IA | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple DCP, POR,2kbit EEPROM Memory, Dual Voltage Monitors |
| X9520V20I-A | 功能描述:IC 3 DCP 2K EE LASR CTRL 20TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
發布緊急采購，3分鐘左右您將得到回復。