- 您現在的位置：買賣IC網 > PDF目錄4277 > XC2S150-6FG456C (Xilinx Inc)IC FPGA 2.5V C-TEMP 456-FBGA PDF資料下載
參數資料
| 型號： | XC2S150-6FG456C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 35/99頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA 2.5V C-TEMP 456-FBGA |
| 標準包裝： | 60 |
| 系列： | Spartan®-II |
| LAB/CLB數： | 864 |
| 邏輯元件/單元數： | 3888 |
| RAM 位總計： | 49152 |
| 輸入/輸出數： | 260 |
| 門數： | 150000 |
| 電源電壓： | 2.375 V ~ 2.625 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 85°C |
| 封裝/外殼： | 456-BBGA |
| 供應商設備封裝： | 456-FBGA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
Spartan-II FPGA Family: Functional Description
DS001-2 (v2.8) June 13, 2008
Module 2 of 4
Product Specification
40
R
LVTTL output buffers have selectable drive strengths.
The format for LVTTL OBUF primitive names is as follows.
OBUF_<slew_rate>_<drive_strength>
<slew_rate> is either F (Fast), or S (Slow) and
<drive_strength> is specified in milliamps (2, 4, 6, 8, 12, 16,
or 24). The default is slew rate limited with 12 mA drive.
OBUF placement restrictions require that within a given
VCCO bank each OBUF share the same output source drive
voltage. Input buffers of any type and output buffers that do
not require VCCO can be placed within any VCCO bank.
Table 17 summarizes the output compatibility requirements.
The LOC property can specify a location for the OBUF.
OBUFT
The generic 3-state output buffer OBUFT, shown in
Figure 39, typically implements 3-state outputs or
bidirectional I/O.
With no extension or property specified for the generic
OBUFT primitive, the assumed standard is slew rate limited
LVTTL with 12 mA drive strength.
The LVTTL OBUFT can support one of two slew rate modes
to minimize bus transients. By default, the slew rate for each
output buffer is reduced to minimize power bus transients
when switching non-critical signals.
LVTTL 3-state output buffers have selectable drive
strengths.
The format for LVTTL OBUFT primitive names is as follows.
OBUFT_<slew_rate>_<drive_strength>
<slew_rate> can be either F (Fast), or S (Slow) and
<drive_strength> is specified in milliamps (2, 4, 6, 8, 12, 16,
or 24).
The Versatile I/O OBUFT placement restrictions require
that within a given VCCO bank each OBUFT share the same
output source drive voltage. Input buffers of any type and
output buffers that do not require VCCO can be placed within
the same VCCO bank.
The LOC property can specify a location for the OBUFT.
3-state output buffers and bidirectional buffers can have
either a weak pull-up resistor, a weak pull-down resistor, or
a weak "keeper" circuit. Control this feature by adding the
appropriate primitive to the output net of the OBUFT
(PULLUP, PULLDOWN, or KEEPER).
The weak "keeper" circuit requires the input buffer within the
IOB to sample the I/O signal. So, OBUFTs programmed for
an I/O standard that requires a VREF have automatic
placement of a VREF in the bank with an OBUFT configured
with a weak "keeper" circuit. This restriction does not affect
most circuit design as applications using an OBUFT
configured with a weak "keeper" typically implement a
bidirectional I/O. In this case the IBUF (and the
corresponding VREF) are explicitly placed.
The LOC property can specify a location for the OBUFT.
IOBUF
Use the IOBUF primitive for bidirectional signals that
require both an input buffer and a 3-state output buffer with
an active high 3-state pin. The generic input/output buffer
IOBUF appears in Figure 40.
With no extension or property specified for the generic
IOBUF primitive, the assumed standard is LVTTL input
buffer and slew rate limited LVTTL with 12 mA drive strength
for the output buffer.
The LVTTL IOBUF can support one of two slew rate modes
to minimize bus transients. By default, the slew rate for each
output buffer is reduced to minimize power bus transients
when switching non-critical signals.
LVTTL bidirectional buffers have selectable output drive
strengths.
The format for LVTTL IOBUF primitive names is as follows:
Table 17: Output Standards Compatibility
Requirements
Rule 1
Only outputs with standards which share
compatible VCCO may be used within the same
bank.
Rule 2
There are no placement restrictions for outputs
with standards that do not require a VCCO.
VCCO
Compatible Standards
3.3
LVTTL, SSTL3_I, SSTL3_II, CTT, AGP, GTL,
GTL+, PCI33_3, PCI66_3
2.5
SSTL2_I, SSTL2_II, LVCMOS2, GTL, GTL+
1.5
HSTL_I, HSTL_III, HSTL_IV, GTL, GTL+
Figure 39: 3-State Output Buffer Primitive (OBUFT
IO
I
IOBUFT
DS001_39_032300
T
相關PDF資料 |
PDF描述 |
|---|---|
| 745530-3 | CONN BACK COVER SLIDE ON DB25 |
| 93AA86A-I/MS | IC EEPROM 16KBIT 2048X8 8-MSOP |
| XC2S150-5FG456I | IC FPGA 2.5V I-TEMP 456-FBGA |
| XC3S500E-4FG320I | IC FPGA SPARTAN 3E 320FBGA |
| 25LC040AT-I/MNY | IC EEPROM SER 4K 512X8 8TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC2S150-6FG456I | 制造商:Xilinx 功能描述: |
| XC2S150-6FGG256C | 制造商:Xilinx 功能描述:FPGA SPARTAN-II 150K GATES 3888 CELLS 263MHZ 2.5V 256FBGA - Trays 制造商:Xilinx 功能描述:FPGA, 864 CLBS, 150000 GATES, 263 MHz, PBGA256 |
| XC2S150-6FGG256I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family |
| XC2S150-6FGG456C | 制造商:Xilinx 功能描述:FPGA SPARTAN-II 150K GATES 3888 CELLS 263MHZ 2.5V 456FBGA - Trays 制造商:Xilinx 功能描述:IC FPGA 260 I/O 456FBGA 制造商:Xilinx 功能描述:IC FPGA SPARTAN-2C 150K 456FBGA |
| XC2S150-6FGG456I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family |
發布緊急采購，3分鐘左右您將得到回復。