參數資料
型號: XC2S200-5FGG456I
廠商: Xilinx Inc
文件頁數: 16/99頁
文件大小: 0K
描述: IC SPARTAN-II FPGA 200K 456-FBGA
標準包裝: 60
系列: Spartan®-II
LAB/CLB數: 1176
邏輯元件/單元數: 5292
RAM 位總計: 57344
輸入/輸出數: 284
門數: 200000
電源電壓: 2.375 V ~ 2.625 V
安裝類型: 表面貼裝
工作溫度: -40°C ~ 100°C
封裝/外殼: 456-BBGA
供應商設備封裝: 456-FBGA
其它名稱: 122-1313
Spartan-II FPGA Family: Functional Description
DS001-2 (v2.8) June 13, 2008
Module 2 of 4
Product Specification
23
R
Master Serial Mode
In Master Serial mode, the CCLK output of the FPGA drives
a Xilinx PROM which feeds a serial stream of configuration
data to the FPGA’s DIN input. Figure 15 shows a Master
Serial FPGA configuring a Slave Serial FPGA from a
PROM. A Spartan-II device in Master Serial mode should
be connected as shown for the device on the left side.
Master Serial mode is selected by a <00x> on the mode
pins (M0, M1, M2). The PROM RESET pin is driven by INIT,
and CE input is driven by DONE. The interface is identical
to the slave serial mode except that an oscillator internal to
the FPGA is used to generate the configuration clock
(CCLK). Any of a number of different frequencies ranging
from 4 to 60 MHz can be set using the ConfigRate option in
the Xilinx software. On power-up, while the first 60 bytes of
the configuration data are being loaded, the CCLK
frequency is always 2.5 MHz. This frequency is used until
the ConfigRate bits, part of the configuration file, have been
loaded into the FPGA, at which point, the frequency
changes to the selected ConfigRate. Unless a different
frequency is specified in the design, the default ConfigRate
is 4 MHz. The frequency of the CCLK signal created by the
internal oscillator has a variance of +45%, –30% from the
specified value.
Figure 17 shows the timing for Master Serial configuration.
The FPGA accepts one bit of configuration data on each
rising CCLK edge. After the FPGA has been loaded, the
data for the next device in a daisy-chain is presented on the
DOUT pin after the rising CCLK edge.
Slave Parallel Mode
The Slave Parallel mode is the fastest configuration option.
Byte-wide data is written into the FPGA. A BUSY flag is
provided for controlling the flow of data at a clock frequency
FCCNH above 50 MHz.
Figure 18, page 24 shows the connections for two
Spartan-II devices using the Slave Parallel mode. Slave
Parallel mode is selected by a <011> on the mode pins (M0,
M1, M2).
If a configuration file of the format .bit, .rbt, or non-swapped
HEX is used for parallel programming, then the most
significant bit (i.e. the left-most bit of each configuration
byte, as displayed in a text editor) must be routed to the D0
input on the FPGA.
The agent controlling configuration is not shown. Typically,
a processor, a microcontroller, or CPLD controls the Slave
Parallel interface. The controlling agent provides byte-wide
configuration data, CCLK, a Chip Select (CS) signal and a
Write signal (WRITE). If BUSY is asserted (High) by the
FPGA, the data must be held until BUSY goes Low.
After configuration, the pins of the Slave Parallel port
(D0-D7) can be used as additional user I/O. Alternatively,
the port may be retained to permit high-speed 8-bit
readback. Then data can be read by de-asserting WRITE.
Figure 17: Master Serial Mode Timing
Serial Data In
CCLK
(Output)
Serial DOUT
(Output)
TDSCK
TCCO
TCKDS
DS001_17_110101
.
Symbol
Description
Units
TDSCK
CCLK
DIN setup
5.0
ns, min
TCKDS
DIN hold
0.0
ns, min
Frequency tolerance with respect to
nominal
+45%, –30%
-
相關PDF資料
PDF描述
AMC35DRXH CONN EDGECARD 70POS .100 DIP SLD
XC2S200-6FG456C IC FPGA 2.5V C-TEMP 456-FBGA
AMM25DTMI CONN EDGECARD 50POS R/A .156 SLD
3341-31BULK CONN JACKSOCKET M2.5/4-40 0.40"
XC2S200-5FG456I IC FPGA 2.5V I-TEMP 456-FBGA
相關代理商/技術參數
參數描述
XC2S200-5PQ208C 功能描述:IC FPGA 2.5V 1176 CLB'S 208-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:Spartan®-II 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA(27x27)
XC2S200-5PQ208I 功能描述:IC FPGA 2.5V I-TEMP 208-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:Spartan®-II 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA(27x27)
XC2S200-5PQ208Q 制造商:Xilinx 功能描述:XILINX XC2S200-5PQ208Q FPGA - Trays 制造商:Xilinx 功能描述:Xilinx XC2S200-5PQ208Q FPGA
XC2S200-5PQG208C 功能描述:IC SPARTAN-II FPGA 200K 208-PQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:Spartan®-II 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA(27x27)
XC2S200-5PQG208I 功能描述:IC SPARTAN-II FPGA 200K 208-PQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:Spartan®-II 標準包裝:60 系列:XP LAB/CLB數:- 邏輯元件/單元數:10000 RAM 位總計:221184 輸入/輸出數:244 門數:- 電源電壓:1.71 V ~ 3.465 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:388-BBGA 供應商設備封裝:388-FPBGA(23x23) 其它名稱:220-1241