參數資料
型號： XC5210-5PC84I
英文描述： Field Programmable Gate Array (FPGA)
中文描述： 現場可編程門陣列（FPGA）
文件頁數： 33/73頁
文件大?。?/td> 598K
代理商： XC5210-5PC84I
R
November 5, 1998 (Version 5.2)
7-115
XC5200 Series Field Programmable Gate Arrays
7
Master Serial Mode
In Master Serial mode, the CCLK output of the lead FPGA
drives a Xilinx Serial PROM that feeds the FPGA DIN input.
Each rising edge of the CCLK output increments the Serial
PROM internal address counter. The next data bit is put on
the SPROM data output, connected to the FPGA DIN pin.
The lead FPGA accepts this data on the subsequent rising
CCLK edge.
The lead FPGA then presents the preamble data—and all
data that overflows the lead device—on its DOUT pin.
There is an internal pipeline delay of 1.5 CCLK periods,
which means that DOUT changes on the falling CCLK
edge, and the next FPGA in the daisy chain accepts data
on the subsequent rising CCLK edge.
In the bitstream generation software, the user can specify
Fast ConfigRate, which, starting several bits into the first
frame, increases the CCLK frequency by a factor of twelve.
The value increases from a nominal 1 MHz, to a nominal 12
MHz. Be sure that the serial PROM and slaves are fast
enough to support this data rate. The Medium ConfigRate
option changes the frequency to a nominal 6 MHz.
XC2000, XC3000/A, and XC3100A devices do not support
the Fast or Medium ConfigRate options.
The SPROM CE input can be driven from either LDC or
DONE. Using LDC avoids potential contention on the DIN
pin, if this pin is configured as user-I/O, but LDC is then
restricted to be a permanently High user output after con-
figuration. Using DONE can also avoid contention on DIN,
provided the DONE before I/O enable option is invoked.
Figure 28 on page 114
shows a full master/slave system.
The leftmost device is in Master Serial mode.
Master Serial mode is selected by a <000> on the mode
pins (M2, M1, M0).
Notes:
1. At power-up, Vcc must rise from 2.0 V to Vcc min in less than 25 ms, otherwise delay configuration by pulling PROGRAM
Low until Vcc is valid.
2. Master Serial mode timing is based on testing in slave mode.
Figure 30: Master Serial Mode Programming Switching Characteristics
In the two Master Parallel modes, the lead FPGA directly
addresses an industry-standard byte-wide EPROM, and
accepts eight data bits just before incrementing or decre-
menting the address outputs.
The eight data bits are serialized in the lead FPGA, which
then presents the preamble data—and all data that over-
flows the lead device—on its DOUT pin. There is an inter-
nal delay of 1.5 CCLK periods, after the rising CCLK edge
that accepts a byte of data (and also changes the EPROM
address) until the falling CCLK edge that makes the LSB
(D0) of this byte appear at DOUT. This means that DOUT
changes on the falling CCLK edge, and the next FPGA in
the daisy chain accepts data on the subsequent rising
CCLK edge.
The PROM address pins can be incremented or decre-
mented, depending on the mode pin settings. This option
allows the FPGA to share the PROM with a wide variety of
microprocessors and microcontrollers. Some processors
must boot from the bottom of memory (all zeros) while oth-
ers must boot from the top. The FPGA is flexible and can
load its configuration bitstream from either end of the mem-
ory.
Master Parallel Up mode is selected by a <100> on the
mode pins (M2, M1, M0). The EPROM addresses start at
00000 and increment.
Master Parallel Down mode is selected by a <110> on the
mode pins. The EPROM addresses start at 3FFFF and
decrement.
Serial Data In
CCLK
(Output)
Serial DOUT
(Output)
1
T
DSCK
2
T
CKDS
n
n + 1
n + 2
n – 3
n – 2
n – 1
n
X3223
Description
Symbol
Min
20
0
Max
Units
ns
ns
CCLK
DIN setup
DIN hold
1
2
T
DSCK
T
CKDS
相關PDF資料
PDF描述
XC5210-5PG223I Field Programmable Gate Array (FPGA)
XC5210-5PQ160I Field Programmable Gate Array (FPGA)
XC5210-5PQ208I Field Programmable Gate Array (FPGA)
XC5210-5PQ240I Field Programmable Gate Array (FPGA)
XC5210-6PQ160I Field Programmable Gate Array (FPGA)
相關代理商/技術參數
參數描述
XC5210-5PG156C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5210-5PG191C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5210-5PG223C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5210-5PG223I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA)
XC5210-5PG299C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*