- 您現在的位置：買賣IC網 > PDF目錄4169 > XC5210-6PQ240C (Xilinx Inc)IC FPGA 324 CLB'S 240-PQFP PDF資料下載
參數資料
| 型號： | XC5210-6PQ240C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 13/73頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA 324 CLB'S 240-PQFP |
| 產品變化通告： | XC1700 PROMs,XC5200,HQ,SCD Parts Discontinuation 19/Jul/2010 |
| 標準包裝： | 24 |
| 系列： | XC5200 |
| LAB/CLB數： | 324 |
| 邏輯元件/單元數： | 1296 |
| 輸入/輸出數： | 196 |
| 門數： | 16000 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 85°C |
| 封裝/外殼： | 240-BFQFP |
| 供應商設備封裝： | 240-PQFP（32x32） |
| 其它名稱： | 122-1151 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
R
XC5200 Series Field Programmable Gate Arrays
7-102
November 5, 1998 (Version 5.2)
tions During Configuration” on page 124, in the “Configura-
tion Timing” section.
Table 9: Pin Descriptions
Pin Name
I/O
During
Config.
I/O
After
Config.
Pin Description
Permanently Dedicated Pins
VCC
I
Five or more (depending on package) connections to the nominal +5 V supply voltage.
All must be connected, and each must be decoupled with a 0.01 - 0.1
F capacitor to
Ground.
GND
I
Four or more (depending on package type) connections to Ground. All must be con-
nected.
CCLK
I or O
I
During configuration, Configuration Clock (CCLK) is an output in Master modes or Asyn-
chronous Peripheral mode, but is an input in Slave mode, Synchronous Peripheral
mode, and Express mode. After configuration, CCLK has a weak pull-up resistor and
can be selected as the Readback Clock. There is no CCLK High time restriction on
XC5200-Series devices, except during Readback. See “Violating the Maximum High
and Low Time Specification for the Readback Clock” on page 113 for an explanation of
this exception.
DONE
I/O
O
DONE is a bidirectional signal with an optional internal pull-up resistor. As an output, it
indicates the completion of the configuration process. As an input, a Low level on
DONE can be configured to delay the global logic initialization and the enabling of out-
puts.
The exact timing, the clock source for the Low-to-High transition, and the optional
pull-up resistor are selected as options in the program that creates the configuration bit-
stream. The resistor is included by default.
PROGRAM
II
PROGRAM is an active Low input that forces the FPGA to clear its configuration mem-
ory. It is used to initiate a configuration cycle. When PROGRAM goes High, the FPGA
executes a complete clear cycle, before it goes into a WAIT state and releases INIT.
The PROGRAM pin has an optional weak pull-up after configuration.
User I/O Pins That Can Have Special Functions
RDY/BUSY
OI/O
During Peripheral mode configuration, this pin indicates when it is appropriate to write
another byte of data into the FPGA. The same status is also available on D7 in Asyn-
chronous Peripheral mode, if a read operation is performed when the device is selected.
After configuration, RDY/BUSY is a user-programmable I/O pin.
RDY/BUSY is pulled High with a high-impedance pull-up prior to INIT going High.
RCLK
OI/O
During Master Parallel configuration, each change on the A0-A17 outputs is preceded
by a rising edge on RCLK, a redundant output signal. RCLK is useful for clocked
PROMs. It is rarely used during configuration. After configuration, RCLK is a user-pro-
grammable I/O pin.
M0, M1, M2
I
I/O
As Mode inputs, these pins are sampled before the start of configuration to determine
the configuration mode to be used. After configuration, M0, M1, and M2 become us-
er-programmable I/O.
During configuration, these pins have weak pull-up resistors. For the most popular con-
figuration mode, Slave Serial, the mode pins can thus be left unconnected. A pull-down
resistor value of 3.3 k
is recommended for other modes.
TDO
O
If boundary scan is used, this pin is the Test Data Output. If boundary scan is not used,
this pin is a 3-state output, after configuration is completed.
This pin can be user output only when called out by special schematic definitions. To
use this pin, place the library component TDO instead of the usual pad symbol. An out-
put buffer must still be used.
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| XC5210-5PQ240C | IC FPGA 324 CLB'S 240-PQFP |
| XC5210-6PQ208C | IC FPGA 324 CLB'S 208-PQFP |
| 88997-2 | CONTACT TIN SOLDER FLAT FLEX |
| ABC65DREI-S93 | CONN EDGECARD 130PS .100 EYELET |
| GMC22DTEF | CONN EDGECARD 44POS .100 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC5210-6PQ240I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| XC5210-6PQG208C | 制造商:Xilinx 功能描述: |
| XC52106T144C | 制造商:Xilinx 功能描述: |
| XC5210-6TQ144C | 功能描述:IC FPGA 324 CLB'S 144-TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC5200 產品變化通告:XC4000(E,L) Discontinuation 01/April/2002 標準包裝:24 系列:XC4000E/X LAB/CLB數:100 邏輯元件/單元數:238 RAM 位總計:3200 輸入/輸出數:80 門數:3000 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:120-BCBGA 供應商設備封裝:120-CPGA（34.55x34.55） |
| XC5210-6TQ144I | 制造商:Xilinx 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。