參數資料
型號： XR16L651CM-F
廠商： Exar Corporation
文件頁數： 3/56頁
文件大?。?/td> 0K
描述： IC UART FIFO 32B 48TQFP
標準包裝： 250
特點： *
通道數： 1，UART
FIFO's： 32 字節
規程： 打印機，RS232，RS422，RS485
電源電壓： 2.25 V ~ 5.5 V
帶并行端口： 是
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
á
XR16L651
REV. 1.3.0
2.25V TO 5.5V UART WITH 32-BYTE FIFO
11
2.2
5-Volt Tolerant Inputs
The 651 can acccept up to 5V inputs even when operating at 3.3V or 2.5V. But note that if the 651 is operating
at 2.5V, its VOH may not be high enough to meet the requirements of the VIH of a CPU or a serial transceiver
that is operating at 5V. Caution: XTAL1 is not 5 volt tolerant.
2.3
Device Reset
The RESET input resets the internal registers and the serial interface outputs to their default state (see
Figure 13). An active high pulse of longer than 40 ns duration will be required to activate the reset function in
the device.
2.4
Device Identification and Revision
The XR16L651 provides a Device Identification code and a Device Revision code to distinguish the part from
other devices and revisions. To read the identification code from the part, it is required to set the baud rate
generator registers DLL and DLM both to 0x00. Now reading the content of the DLM will provide 0x04 for the
XR16L651 and reading the content of DLL will provide the revision of the part; for example, a reading of 0x01
means revision A.
2.5
DMA Mode
The device does not support direct memory access. The DMA Mode (a legacy term) in this document does not
mean “direct memory access” but refers to data block transfer operation. The DMA mode affects the state of
the RXRDY# and TXRDY# output pins. The transmit and receive FIFO trigger levels provide additional
flexibility to the user for block mode operation. The LSR bits 5-6 provide an indication when the transmitter is
empty or has an empty location(s) for more data. The user can optionally operate the transmit and receive
FIFO in the DMA mode (FCR bit-3=1). When the transmit and receive FIFO are enabled and the DMA mode is
disabled (FCR bit-3 = 0), the 651 is placed in single-character mode for data transmit or receive operation.
When DMA mode is enabled (FCR bit-3 = 1), the user takes advantage of block mode operation by loading or
unloading the FIFO in a block sequence determined by the programmed trigger level. In this mode, the 651
sets the TXRDY# pin when the transmit FIFO becomes full, and sets the RXRDY# pin when the receive FIFO
becomes empty. The following table shows their behavior. Also see Figures 26 through 31.
TABLE 2: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE
PINS
FCR BIT-0=0
(FIFO DISABLED)
FCR BIT-0=1 (FIFO ENABLED)
FCR BIT-3 = 0
(DMA MODE DISABLED)
FCR BIT-3 = 1
(DMA MODE ENABLED)
RXRDY#
0 = 1 byte.
1 = no data.
0 = at least 1 byte in FIFO
1 = FIFO empty.
1 to 0 transition when FIFO reaches the trigger
level, or timeout occurs.
0 to 1 transition when FIFO empties.
TXRDY#
0 = THR empty.
1 = byte in THR.
0 = FIFO empty.
1 = at least 1 byte in FIFO.
0 = FIFO has at least 1 empty location.
1 = FIFO is full.
相關PDF資料
PDF描述
XR68C92IJTR-F DUAL CHANNEL UART 44PLCC
XR68C192CVTR-F IC UART FIFI DUAL 44LQFP
ST16C650AIQ48-F IC UART FIFO 32B 48TQFP
XR16L2450IM-F IC UART FIFO 1B DUAL 48TQFP
XR68C192CJTR-F IC UART FIFI DUAL 44PLCC
相關代理商/技術參數
參數描述
XR16L651CMTR-F 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 2.5V/3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16L651CMTR-F
XR16L651IM 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16L651IM-F 功能描述:UART 接口集成電路 UARTW/32BYTEFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L651IMTR-F 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 2.5V/3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16L651IMTR-F
XR16L784 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*