參數資料
型號: XR16L651CM-F
廠商: Exar Corporation
文件頁數: 53/56頁
文件大小: 0K
描述: IC UART FIFO 32B 48TQFP
標準包裝: 250
特點: *
通道數: 1,UART
FIFO's: 32 字節
規程: 打印機,RS232,RS422,RS485
電源電壓: 2.25 V ~ 5.5 V
帶并行端口:
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 48-TQFP
供應商設備封裝: 48-TQFP(7x7)
包裝: 托盤
XR16L651
á
2.25V TO 5.5V UART WITH 32-BYTE FIFO
REV. 1.3.0
6
Pin type: I=Input, O=Output, IO= Input/output, OD=Output Open Drain.
XTAL1
14
I
Crystal or external clock input. Caution: this input is not 5V tolerant.
XTAL2
15
O
Crystal or buffered clock output
RCLK
5
I
Receiver Clock
This input is used as external 16X clock input to the receiver section. Connect
the BAUDOUT# pin to this input externally.
BAUDOUT#
12
O
Baud Rate Generator Output (active low)
This pin provides the 16X clock of the selected data rate from the baud rate
generator. The RCLK pin must be connected externally to BAUDOUT# when
the receiver is operating at the same data rate.
When the PC mode is selected, the baud rate generator clock output is inter-
nally connected to the RCLK input. This pin then functions as the LPT-1
printer port decode logic output, see
PCMODE#
36
I
PC Mode Select (active low)
When this input is at logic 0, it enables the on-board chip select decode func-
tion according to PC ISA bus COM[4:1] and IRQ[4:3] port definitions. See
Table 3 for details. This pin has an internal 100k
pull-up resistor.
DDIS#
22
O
Drive Disable Output
This pin goes to a logic 0 whenever the host CPU is reading data from the
651. It can control the direction of a data bus transceiver between the CPU
and 651 or other logic functions.
ENIR
13
I
Enable Infrared Mode (active high)
This pin can be used to start up the UART in wireless infrared mode. This
input is sampled when the reset input signal (RESET or RESET#) is de-
asserted. The TX output would idle at logic 0 instead of normal logic 1. The
software infrared enable bit (MCR bit-6) will have full enable/disable control
after the power up.
RESET
(RESET#)
35
I
Reset Input
A 40 ns minimum active pulse on this pin will reset the internal registers and
all outputs. The UART transmitter output will be held at logic 1 (if ENIR pin is
at a logic 0), the receiver input will be ignored and outputs are reset. See
UART Reset Conditions in
Table 13. When IM# pin is at a logic 0, Intel bus
mode, reset input is active high. When IM# pin is at a logic 1, Motorola bus
mode, reset input is active low.
IM#
37
I
Intel or Motorola data bus interface select
A logic 0 selects Intel bus interface and a logic 1 selects Motorola interface.
This input affects the functionality of IOR#, IOW#, CS# and INT pins.
OP1#
34
O
Output Port 1
General purpose output.
OP2#
31
O
Output Port 2
General purpose output.
VCC
43
Pwr
2.25V to 5.5V supply voltage
All inputs, except XTAL1, are 5V tolerant.
GND
18
Pwr
Power supply common ground.
NC
1,25
-
No Connect
NAME
PIN #TYPE
DESCRIPTION
相關PDF資料
PDF描述
XR68C92IJTR-F DUAL CHANNEL UART 44PLCC
XR68C192CVTR-F IC UART FIFI DUAL 44LQFP
ST16C650AIQ48-F IC UART FIFO 32B 48TQFP
XR16L2450IM-F IC UART FIFO 1B DUAL 48TQFP
XR68C192CJTR-F IC UART FIFI DUAL 44PLCC
相關代理商/技術參數
參數描述
XR16L651CMTR-F 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 2.5V/3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16L651CMTR-F
XR16L651IM 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16L651IM-F 功能描述:UART 接口集成電路 UARTW/32BYTEFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L651IMTR-F 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 2.5V/3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16L651IMTR-F
XR16L784 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART