參數資料
型號: XR16L651IM-F
廠商: Exar Corporation
文件頁數: 11/56頁
文件大?。?/td> 0K
描述: IC UART FIFO 32B 48TQFP
標準包裝: 250
特點: *
通道數: 1,UART
FIFO's: 32 字節
規程: 打印機,RS232,RS422,RS485
電源電壓: 2.25 V ~ 5.5 V
帶并行端口:
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 48-TQFP
供應商設備封裝: 48-TQFP(7x7)
包裝: 托盤
á
XR16L651
REV. 1.3.0
2.25V TO 5.5V UART WITH 32-BYTE FIFO
19
In the event that the receive buffer is overfilling and flow control needs to be executed, the 651 automatically
sends an Xoff message (when enabled) via the serial TX output to the remote modem. The 651 sends the Xoff-
1,2 characters two-character-times (= time taken to send two characters at the programmed baud rate) after
the receive FIFO crosses the programmed trigger level. To clear this condition, the 651 will transmit the
programmed Xon-1,2 characters as soon as receive FIFO drops to one trigger level below the programmed
trigger level. Table 5 below explains this:
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2
characters); for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting.
2.14
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The 651 compares each incoming receive character with Xoff-2 data. If a match exists, the received data will
be transferred to the RX FIFO and ISR bit-4 will be set to indicate detection of a special character.
Although the Internal Register Table shows each X-Register with eight bits of character information, the actual
number of bits is dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the
number of character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1
also determines the number of bits that will be used for the special character comparison. Bit-0 in the X-
registers corresponds with the LSB bit for the receive character.
2.15
Auto RS485 Half-duplex Control
The auto RS485 half-duplex direction control changes the behavior of the transmitter when enabled by XFR
bit-3. By default, it asserts RTS# (logic 0) output following the last stop bit of the last character that has been
transmitted. This helps in turning around the transceiver to receive the remote station’s response. When the
host is ready to transmit next polling data packet again, it only has to load data bytes to the transmit FIFO. The
transmitter automatically re-asserts RTS# (logic 1) output prior to sending the data. The RS485 half-duplex
direction control output polarity can be inverted by enabling XFR bit-5.
TABLE 5: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
XOFF CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
XON CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
88
8*
0
16
16*
8
24
24*
16
28
28*
24
TABLE 6: RS485 HALF-DUPLEX CONTROL
XFR BIT-2
XFR BIT-5
RTS# PIN
0
X
RS485 Half-Duplex control disabled
1
0
Logic 1 = TX
Logic 0 = RX
1
Logic 1 = RX
Logic 0 = TX
相關PDF資料
PDF描述
XR16L784IV-F IC UART 8B 3.3V QUAD 64LQFP
XR16L788IQ-F IC UART 64B 3.3V OCTAL 100QFP
XR16M2550IL32-F IC UART FIFO 16B 1.8V DUAL 32QFN
XR16M2551IL32-F IC UART FIFO 16B DUAL 32QFN
XR16M2650IM48-F IC UART FIFO 32B DUAL 48TQFP
相關代理商/技術參數
參數描述
XR16L651IMTR-F 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 2.5V/3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16L651IMTR-F
XR16L784 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
XR16L784_05 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
XR16L784_08 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
XR16L78464-TQFP 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART