- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L784 (Exar Corporation) HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART PDF資料下載
參數資料
| 型號： | XR16L784 |
| 廠商： | Exar Corporation |
| 英文描述： | HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| 中文描述： | 高性能2.97V至5.5V UART的四 |
| 文件頁數： | 33/52頁 |
| 文件大?。?/td> | 625K |
| 代理商： | XR16L784 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
á
REV. 1.2.0
XR16L784
HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
33
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) - Read/Write
The MCR register is used for controlling the modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin may be used for automatic hardware flow control enabled by EFR bit-6 and MCR bit-2=1. If the
modem interface is not used, this output may be used for general purpose.
Logic 0 = Force DTR# output to a logic 1 (default).
Logic 1 = Force DTR# output to a logic 0.
MCR[1]: RTS# Output
The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit-6 and MCR bit-2=0. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force RTS# output to a logic 1 (default).
Logic 1 = Force RTS# output to a logic 0.
MCR[2]: RTS/CTS or DTR/DSR for Auto Flow Control
DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by
EFR bit-6.
Logic 0 = RTS# (RX side) and CTS# (TX side) pins are used for auto hardware flow control (default).
Logic 1 = DTR# (RX side) and DSR# (TX side) pins are used for auto hardware flow control.
MCR[3]: Reserved
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and
Figure 12
.
MCR[5]: Xon-Any Enable
Logic 0 = Disable Xon-Any function (default).
Logic 1 = Enable Xon-Any function. In this mode any RX character received will enable Xon, resume data
transmission.
MCR[6]: Infrared Encoder/Decoder Enable
The state of this bit depends on the sampled logic level of pin ENIR during power up, following a hardware
reset (rising edge of RST# input). Afterward user can override this bit for desired operation.
Logic 0 = Enable the standard modem receive and transmit character interface.
Logic 1 = Enable infrared IrDA receive and transmit inputs/outputs. While in this mode, the TX/RX output/
input are routed to the infrared encoder/decoder. The data input and output levels will conform to the IrDA
infrared interface requirement. As such, while in this mode the infrared TX output will be a logic 0 during idle
data conditions. FCTR bit-4 may be selected to invert the RX input signal level going to the decoder for
infrared modules that provide rather an inverted output.
MCR[7]: Clock Prescaler Select
Logic 0 = Divide by one. The input clock from the crystal or external clock is fed directly to the Programmable
Baud Rate Generator without further modification, i.e., divide by one (default).
Logic 1 = Divide by four. The prescaler divides the input clock from the crystal or external clock by four and
feeds it to the Programmable Baud Rate Generator, hence, data rates become one forth.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L78464-TQFP | HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L784CV | HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L784IV | HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L788 | HIGH PERFORMANCE OCTAL UART |
| XR16L788CQ | HIGH PERFORMANCE OCTAL UART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L784_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L784_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L78464-TQFP | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L784CV | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L784CV-0A-EVB | 功能描述:UART 接口集成電路 Supports L784 64 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。