- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L788 (Exar Corporation) HIGH PERFORMANCE OCTAL UART PDF資料下載
參數資料
| 型號： | XR16L788 |
| 廠商： | Exar Corporation |
| 英文描述： | HIGH PERFORMANCE OCTAL UART |
| 中文描述： | 高性能八進制的UART |
| 文件頁數： | 12/42頁 |
| 文件大小： | 557K |
| 代理商： | XR16L788 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
áyyyyyyyyyyyy
XR16L788 OCTAL UART
REV. 1.1.4
12
identification. A return value of 0x28 from this register
indicates the device is a XR16L788. The DREV regis-
ter returns a 8-bit value of 0x01 for revision A, 0x02
for revision B and so on. This information is very use-
ful to the software driver for identifying which device it
is communicating with and to keep up with revision
changes.
DVID [7:0] default 0x28)
Device identification for the type of UART. The upper
nibble indicates it is a XR16L78x series with lower
nibble indicating the number of channels.
Examples:
XR16L788 = 0x28
XR16L784 = 0x24
DREV [7:0] (default (0x01)
Revision number of the XR16L788. A 0x01 repre-
sents "revision-A" with 0x02 for rev-B and so forth.
1.1.8
REGB [7:0] (default 0x00)
REGB register provides a control for simultaneous
write to all 8 UARTs configuration registers or individ-
ually. This is very useful for device initialization in the
power up and reset routines.
2.0
The 788 includes an on-chip oscillator (XTAL1 and
XTAL2). The crystal oscillator provides the system
clock to the Baud Rate Generators (BRG) in each of
the 8 UARTs, the 16-bit general purpose timer/
counter and internal logics. XTAL1 is the input to the
oscillator or external clock buffer input with XTAL2 pin
being the output. For programming details, see “Pro-
grammable Baud Rate Generator” on page 13.
The on-chip oscillator is designed to use an industry
standard microprocessor crystal (parallel resonant
with 10-22 pF capacitance load, 100ppm) connected
CRYSTAL OSCILLATOR / BUFFER
externally between the XTAL1 and XTAL2 pins (see
Figure 6
). Alternatively, an external clock can be con-
nected to the XTAL1 pin to clock the internal 8 baud
rate generators for standard or custom rates. Typical-
ly, the oscillator connections are shown in Figure 6.
For further reading on oscillator circuit please see ap-
plication note DAN108 on EXAR’s web site.
3.0
Each UART channel has a transmit holding register
(THR) and a receive holding register (RHR). The
THR and RHR registers are 16550 compatible so
their access is limited to 8-bit format. The software
driver must separately read the LSR content for the
associated error flags before reading the data byte.
TRANSMIT AND RECEIVE DATA
3.1
FIFO
DATA LOADING AND UNLOADING
THROUGH THE UART CHANNEL REGIS-
TERS, THR AND RHR.
The THR and RHR register addresses for channel 0
to channel 7 is shown in
Table 5
below. The THR and
RHR for channels 0 to 7 are located at address 0x00,
0x10, 0x20, 0x30, 0x40, 0x50, 0x60 and 0x70 respec-
tively. Transmit data byte is loaded to the THR when
writing to that address and receive data is unloaded
from the RHR register when reading that address.
Both THR and RHR registers are 16C550 compatible
in 8-bit format, so each bus operation can only write
or read in bytes.
REGB[0]
Logic 0 (default) write to each UART
configuration registers individually.
Logic 1 enables simultaneous write to
all 8 UARTs configuration register. Use-
ful during device initialization.
Reserved
REGB[7:1]
F
IGURE
6. T
YPICAL
OSCILLATOR
CONNECTIONS
C1
22-47pF
C2
22-47pF
14.7456
MHz
XTAL1
XTAL2
R=300K to 400K
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L788CQ | HIGH PERFORMANCE OCTAL UART |
| XR16L788IQ | HIGH PERFORMANCE OCTAL UART |
| XR17C154 | Tip, Offset Tapered Needle, 1mm Diameter |
| XR17C154CV | Burner |
| XR17C154IV | Tools, Heatgun; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No RoHS Compliant: No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L788_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART |
| XR16L788_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART |
| XR16L788CQ | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART |
| XR16L788CQ-0A-EVB | 功能描述:UART 接口集成電路 Supports L788 100 ld QFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L788CQ-0B-EVB | 功能描述:界面開發工具 Supports L788 100 ld QFP, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。