參數資料
型號： XR16L788
廠商： Exar Corporation
英文描述： HIGH PERFORMANCE OCTAL UART
中文描述： 高性能八進制的UART
文件頁數： 28/42頁
文件大?。?/td> 557K
代理商： XR16L788
áyyyyyyyyyyyy
XR16L788 OCTAL UART
REV. 1.1.4
28
Modem Status Register (MSR) - Read Only
This register provides the current state of the modem
interface signals, or other peripheral device that the
UART is connected. Lower four bits of this register
are used to indicate the changed information. These
bits are set to a logic 1 whenever a signal from the
modem changes state. These bits may be used as
general purpose inputs/outputs when they are not
used with modem signals.
MSR[0]: Delta CTS# Input Flag
Logic 0 = No change on CTS# input (default).
Logic 1 = The CTS# input has changed state since
the last time it was monitored. A modem status
interrupt will be generated if MSR interrupt is
enabled (IER bit-3.
MSR[1]: Delta DSR# Input Flag
Logic 0 = No change on DSR# input (default).
Logic 1 = The DSR# input has changed state since
the last time it was monitored. A modem status
interrupt will be generated if MSR interrupt is
enabled (IER bit-3.
MSR[2]: Delta RI# Input Flag
Logic 0 = No change on RI# input (default).
Logic 1 = The RI# input has changed from a logic 0
to a logic 1, ending of the ringing signal. A modem
status interrupt will be generated if MSR interrupt is
enabled (IER bit-3.
MSR[3]: Delta CD# Input Flag
Logic 0 = No change on CD# input (default).
Logic 1 = Indicates that the CD# input has changed
state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is
enabled (IER bit-3.
MSR[4]: CTS Input Status
CTS# pin may function as automatic hardware flow
control signal input if it is enabled and selected by Au-
to CTS (EFR bit-7) and RTS/CTS flow control select
(MCR bit-2). Auto CTS flow control allows starting
and stopping of local data transmissions based on
the modem CTS# signal. A logic 1 on the CTS# pin
will stop UART transmitter as soon as the current
character has finished transmission, and a logic 0 will
resume data transmission. Normally MSR bit-4 bit is
the compliment of the CTS# input. However in the
loopback mode, this bit is equivalent to the RTS# bit
in the MCR register. The CTS# input may be used as
a general purpose input when the modem interface is
not used.
MSR[5]: DSR Input Status
DSR#
(active high, logical 1). This input may be used
for auto DTR/DSR flow control function, see auto
\hardware flow control section. Normally this bit is the
compliment of the DSR# input. In the loopback mode,
this bit is equivalent to the DTR# bit in the MCR regis-
ter. The DSR# input may be used as a general pur-
pose input when the modem interface is not used.
MSR[6]: RI Input Status
RI# (active high, logical 1). Normally this bit is the
compliment of the RI# input. In the loopback mode
this bit is equivalent to bit-2 in the MCR register. The
RI# input may be used as a general purpose input
when the modem interface is not used.
MSR[7]: CD Input Status
CD# (active high, logical 1). Normally this bit is the
compliment of the CD# input. In the loopback mode
this bit is equivalent to bit-3 in the MCR register. The
CD# input may be used as a general purpose input
when the modem interface is not used.
Modem Status Register (MSR) - Write Only
The upper four bits 4-7 of this register sets the delay
in number of bits time for the auto RS485 turn around
from transmit to receive.
MSR [7:4]
When Auto RS485 feature is enabled (FCTR bit-5=1)
and RTS# output is connected to the enable input of
a RS-485 transceiver. These 4 bits select from 0 to 15
bit-time delay after the end of the last stop-bit of the
last transmitted character. This delay controls when
to change the state of RTS# output. This delay is very
useful in long-cable networks. Table 12 shows the se-
lection. The bits are enabled by EFR bit-4.
相關PDF資料
PDF描述
XR16L788CQ HIGH PERFORMANCE OCTAL UART
XR16L788IQ HIGH PERFORMANCE OCTAL UART
XR17C154 Tip, Offset Tapered Needle, 1mm Diameter
XR17C154CV Burner
XR17C154IV Tools, Heatgun; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No RoHS Compliant: No
相關代理商/技術參數
參數描述
XR16L788_05 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
XR16L788_08 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
XR16L788CQ 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
XR16L788CQ-0A-EVB 功能描述:UART 接口集成電路 Supports L788 100 ld QFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L788CQ-0B-EVB 功能描述:界面開發工具 Supports L788 100 ld QFP, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*