REV. 1.0.2 ISR[0]: Interrupt Status " />
參數資料
型號： XR16M2650IL32-F
廠商： Exar Corporation
文件頁數： 19/47頁
文件大?。?/td> 0K
描述： IC UART FIFO 32B DUAL 32QFN
標準包裝： 490
特點： *
通道數： 2，DUART
FIFO's： 32 字節
規程： RS232，RS422
電源電壓： 1.62 V ~ 3.63 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤
供應商設備封裝： 32-QFN 裸露焊盤（5x5）
包裝： 托盤
XR16M2650
26
HIGH PERFORMANCE LOW VOLTAGE DUART WITH 32-BYTE FIFO
REV. 1.0.2
ISR[0]: Interrupt Status
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending (default condition).
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source
ISR[4]: Xoff/Xon or Special Character Interrupt Status
This bit is enabled when EFR bit-4 is set to HIGH. ISR bit-4 indicates that the receiver detected a data match of
the Xoff character(s). If this is an Xoff/Xon interrupt, it can be cleared by a read to the ISR. If it is a special
character interrupt, it can be cleared by reading ISR or it will automatically clear after the next character is
received.
ISR[5]: RTS#/CTS# Interrupt Status
This bit is enabled when EFR bit-4 is set to HIGH. ISR bit-5 indicates that the CTS# or RTS# has been de-
asserted.
ISR[7:6]: FIFO Enable Status
These bits are set to LOW when the FIFOs are disabled. They are set to HIGH when the FIFOs are enabled.
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to HIGH when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers (the receive shift register is not cleared or altered). This bit will
return to LOW after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers (the transmit shift register is not cleared or altered). This bit will
return to LOW after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
相關PDF資料
PDF描述
1-1776244-9 TERM BLOCK RCPT 19POS VERT 5MM
1-1776244-8 TERM BLOCK RCPT 18POS VERT 5MM
1-1776244-7 TERM BLOCK RCPT 17POS VERT 5MM
1-1776244-6 TERM BLOCK RCPT 16POS VERT 5MM
1-1776244-5 TERM BLOCK RCPT 15POS VERT 5MM
相關代理商/技術參數
參數描述
XR16M2650IM-0B-EB 功能描述:UART 接口集成電路 Supports M2650 48 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M2650IM48 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16M2650IM48-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M2651 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO AND POWERSAVE FEATURE
XR16M2651IL-0B-EB 功能描述:UART 接口集成電路 Supports M2651 32pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*