- 您現在的位置：買賣IC網 > PDF目錄11820 > XR17V252IM-F (Exar Corporation)IC UART PCI BUS DUAL 100TQFP PDF資料下載
參數資料
| 型號： | XR17V252IM-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 42/69頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART PCI BUS DUAL 100TQFP |
| 標準包裝： | 90 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 64 字節 |
| 規程： | RS485 |
| 電源電壓： | 3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-TQFP |
| 供應商設備封裝： | 100-TQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
XR17V252
47
REV. 1.0.2
66 MHZ PCI BUS DUAL UART WITH POWER MANAGEMENT SUPPORT
MCR[3]: Send Char Immediate (OP2 in Local Loopback Mode)
This bit is used to transmit a character immediately irrespective of the bytes currently in the transmit FIFO. The
data byte must be loaded into the transmit holding register (THR) immediately following the write to this bit (to
set it to a ’1’). In other words, no other register must be accessed between setting this bit and writing to the
THR. The loaded byte will be transmitted ahead of all the bytes in the TX FIFO, immediately after the character
currently being shifted out of the transmit shift register is sent out. The existing line parameters (parity, stop
bits) will be used when composing the character. This bit is self clearing, therefore, must be set before sending
a custom character each time. Please note that the Transmitter must be enabled for this function (MSR[3] = 0).
Also, if software flow control is enabled, the software flow control characters (Xon, Xoff) have higher priority
and will get shifted out before the custom byte is transmitted.
Logic 0 = Send Char Immediate disabled (default).
Logic 1 = Send Char Immediate enabled.
In Local Loopback Mode (MCR[4] = 1), this bit acts as the legacy OP2 output and controls the CD bit in the
MSR register as shown in Figure 14. Please make sure that this bit is a ’0’ when exiting the Local Loopback
Mode.
MCR[2]: DTR# or RTS# for Auto Flow Control (OP1 in Local Loopback Mode)
DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by
EFR bit [6]. DTR# selection is associated with DSR# and RTS# is with CTS#.
Logic 0 = Uses RTS# and CTS# pins for auto hardware flow control.
Logic 1 = Uses DTR# and DSR# pins for auto hardware flow control.
In Local Loopback mode (MCR[4] = 1), this bit acts as the legacy OP1 output and controls the RI bit in the MSR
register, as shown in Figure 14.
MCR[1]: RTS# Output
The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit [6] and MCR bit [2]=0. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force RTS# output to a HIGH (default).
Logic 1= Force RTS# output to LOW.
MCR[0]: DTR# Output
The DTR# pin may be used for automatic hardware flow control enabled by EFR bit [6] and MCR bit [2]=1. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force DTR# output to a HIGH (default).
Logic 1 = Force DTR# output to a LOW.
5.9
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host. If IER bit [2] is set to a
logic 1, an LSR interrupt will be generated immediately when any character in the RX FIFO has an error (parity,
framing, overrun, break).
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error (default).
Logic 1 = An indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error or
break indication is in the FIFO data. This bit clears when there are no more errors in the FIFO.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3110E14-15S | CONN RCPT 15POS WALL MNT W/SCKT |
| SCC2692AE1B44,557 | IC UART DUAL W/FIFO 44PLCC |
| MS27467T13B4P | CONN PLUG 4POS STRAIGHT W/PINS |
| MS27484T16F26S | CONN PLUG 26POS STRAIGHT W/SCKT |
| SC26C92C1A,512 | IC UART DUAL W/FIFO 44-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17V252IMTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 3.3V 100-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR17V252IMTR-F |
| XR17V254 | 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT |
| XR17V254_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT |
| XR17V254IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT |
| XR17V254IV-0A-EVB | 功能描述:UART 接口集成電路 Supports V254 144 ld LQFP,PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。