REV. 1.1.1 HIGH PERFORMANCE DUART WITH 64-BYTE FIFO 2.14 Auto CTS Flow Control Automatic CTS flow control is" />
參數資料
型號： XR68M752IM48-F
廠商： Exar Corporation
文件頁數： 11/54頁
文件大?。?/td> 0K
描述： IC UART FIFO 64B DUAL 48TQFP
標準包裝： 250
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS232，RS422，RS485
電源電壓： 1.62 V ~ 3.63 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
其它名稱： 1016-1479
1016-1479-ND
1016-1642
XR68M752IM48-F-ND
XR16M752/XR68M752
19
REV. 1.1.1
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
2.14
Auto CTS Flow Control
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS# input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see Figure 11):
Enable auto CTS flow control using EFR bit-7.
If using the Auto CTS interrupt:
Enable CTS interrupt through IER bit-7 (after setting EFR bit-4). The UART issues an interrupt when the
CTS# pin is de-asserted (HIGH): ISR bit-5 will be set to 1, and UART will suspend transmission as soon as
the stop bit of the character in process is shifted out. Transmission is resumed after the CTS# input is re-
asserted (LOW), indicating more data may be sent.
FIGURE 11. AUTO RTS AND CTS FLOW CONTROL OPERATION
RTSA#
CTSB#
RXA
TXB
Transmitter
Receiver FIFO
Trigger Reached
Auto RTS
Trigger Level
Auto CTS
Monitor
RTSA#
TXB
RXA FIFO
CTSB#
Remote UART
UARTB
Local UART
UARTA
ON
OFF
ON
Suspend
Restart
RTS High
Threshold
Data Starts
ON
OFF
ON
Assert RTS# to Begin
Transmission
1
2
3
4
5
6
7
Receive
Data
RTS Low
Threshold
9
10
11
Receiver FIFO
Trigger Reached
Auto RTS
Trigger Level
Transmitter
Auto CTS
Monitor
RTSB#
CTSA#
RXB
TXA
INTA
(RXA FIFO
Interrupt)
RX FIFO
Trigger Level
RX FIFO
Trigger Level
8
12
RTSCTS1
The local UART (UARTA) starts data transfer by asserting RTSA# (1). RTSA# is normally connected to CTSB# (2) of
remote UART (UARTB). CTSB# allows its transmitter to send data (3). TXB data arrives and fills UARTA receive FIFO
(4). When RXA data fills up to its receive FIFO trigger level, UARTA activates its RXA data ready interrupt (5) and con-
tinues to receive and put data into its FIFO. If interrupt service latency is long and data is not being unloaded, UARTA
monitors its receive data fill level to match the upper threshold of RTS delay and de-assert RTSA# (6). CTSB# follows
(7) and request UARTB transmitter to suspend data transfer. UARTB stops or finishes sending the data bits in its trans-
mit shift register (8). When receive FIFO data in UARTA is unloaded to match the lower threshold of RTS delay (9),
UARTA re-asserts RTSA# (10), CTSB# recognizes the change (11) and restarts its transmitter and data flow again until
next receive FIFO trigger (12). This same event applies to the reverse direction when UARTA sends data to UARTB
with RTSB# and CTSA# controlling the data flow.
相關PDF資料
PDF描述
XR16M752IM48-F IC UART FIFO 34B DUAL 48TQFP
ST16C450CQ48-F IC UART SINGLE 48TQFP
ST16C2450IQ48-F IC UART FIFO DUAL 48TQFP
MAX7314AEG+T IC I/O EXPANDER I2C 16B 24QSOP
ST16C550IQ48-F IC UART FIFO 16B SGL 48TQFP
相關代理商/技術參數
參數描述
XR68M752IM48TR-F 制造商:Exar Corporation 功能描述:XR68M752 Series 16 Mbps High Performance DUART With 64-Byte FIFO - TQFP-48
XR7090AA-BC-0001 制造商:CREE 制造商全稱:Cree, Inc 功能描述:XLamp㈢ XR LED Binning and Labeling
XR7090AA-BC-DD-EF-G-HHHH 制造商:CREE 制造商全稱:Cree, Inc 功能描述:XLamp㈢ XR LED Binning and Labeling
XR7090-AM-L1-0001 制造商:Cree 功能描述:LED AMBER XR 制造商:Cree 功能描述:LED, AMBER, XR 制造商:Cree 功能描述:LED, HIGH BRIGHTNESS, RED ORANGE, 67.2LM; Series:XLamp XR; LED Color:Amber; Luminous Flux @ Test:42lm; Wavelength Typ:595nm; Forward Current @ Test:350mA; Forward Current If Max:700mA; Forward Voltage @ Test:2.25V; Viewing Angle:100;RoHS Compliant: Yes
XR7090AM-L1-0001 制造商:Cree 功能描述:LED Uni-Color Amber 2-Pin SMD
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*