參數資料
型號： XRT16C854
廠商： Exar Corporation
英文描述： 2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
中文描述： 2.97V至5.5V四路UART的128字節FIFO
文件頁數： 5/54頁
文件大?。?/td> 485K
代理商： XRT16C854
xr
REV. 3.0.1
XR16C854/854D
2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
5
CSD#
(N.C.)
42
54
68
I
When 16/68# pin is at logic 1, this input is chip select D (active low)
to enable channel D in the device.
When 16/68# pin is at logic 0, this input is not used.
Motorola bus interface is not available on the 64 pin package.
INTA
(IRQ#)
6
15
12
O
(OD)
When 16/68# pin is at logic 1 for Intel bus interface, this ouput
becomes channel A interrupt output. The output state is defined by
the user and through the software setting of MCR[3]. INTA is set to
the active mode when MCR[3] is set to a logic 1. INTA is set to the
three state mode when MCR[3] is set to a logic 0 (default). See
MCR[3].
When 16/68# pin is at logic 0 for Motorola bus interface, this output
becomes device interrupt output (active low, open drain). An exter-
nal pull-up resistor is required for proper operation.
Motorola bus interface is not available on the 64 pin package.
INTB
INTC
INTD
(N.C.)
12
37
43
21
49
55
18
63
69
O
When 16/68# pin is at logic 1 for Intel bus interface, these ouputs
become the interrupt outputs for channels B, C, and D. The output
state is defined by the user through the software setting of MCR[3].
The interrupt outputs are set to the active mode when MCR[3] is
set to a logic 1 and are set to the three state mode when MCR[3] is
set to a logic 0 (default). See MCR[3].
When 16/68# pin is at logic 0 for Motorola bus interface, these out-
puts are unused and will stay at logic zero level. Leave these out-
puts unconnected.
Motorola bus interface is not available on the 64 pin package.
INTSEL
-
65
87
I
Interrupt Select (active high, input with internal pull-down).
When 16/68# pin is at logic 1 for Intel bus interface, this pin can be
used in conjunction with MCR bit-3 to enable or disable the INT A-
D pins or override MCR bit-3 and enable the interrupt outputs.
Interrupt outputs are enabled continuously by making this pin a
logic 1. Making this pin a logic 0 allows MCR bit-3 to enable and
disable the interrupt output pins. In this mode, MCR bit-3 is set to
a logic 1 to enable the continuous output. See MCR bit-3 descrip-
tion for full detail. This pin must be at logic 0 in the Motorola bus
interface mode. Due to pin limitations on 64 pin packages, this pin
is not available. To cover this limitation, two 64 pin LQFP pack-
ages versions are offered. The XR16C854D operates in the con-
tinuous interrupt enable mode by bonding this pin to VCC
internally.
TXRDYA#
TXRDYB#
TXRDYC#
TXRDYD#
-
-
-
-
-
-
-
-
5
25
56
81
O
UART channels A-D Transmitter Ready (active low). The outputs
provide the TX FIFO/THR status for transmit channels A-D. See
Table 5
. If these outputs are unused, leave them unconnected.
RXRDYA#
RXRDYB#
RXRDYC#
RXRDYD#
-
-
-
-
-
-
-
-
100
31
50
82
O
UART channels A-D Receiver Ready (active low). This output pro-
vides the RX FIFO/RHR status for receive channels A-D. See
Table 5
. If these outputs are unused, leave them unconnected.
Pin Description
N
AME
64-LQFP
P
IN
#
68-PLCC
P
IN
#
100-QFP
P
IN
#
T
YPE
D
ESCRIPTION
相關PDF資料
PDF描述
XRT16L2552 2.25V TO 5.5V DUART WITH 16-BYTE FIFO
XRT3591 SINGLECHIP V. 35 TRANSCEIVER
XRT3591B SINGLECHIP V. 35 TRANSCEIVER
XRT3591BID SINGLECHIP V. 35 TRANSCEIVER
XRT3591BIP SINGLECHIP V. 35 TRANSCEIVER
相關代理商/技術參數
參數描述
XRT16L2552 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 16-BYTE FIFO
XRT2588CN 制造商:Exar Corporation 功能描述:
XR-T2713CP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Subscriber Line Metering/Monitoring Circuit
XR-T3588 制造商:EXAR 制造商全稱:EXAR 功能描述:V.35 Interface Receiver/Transmitter
XR-T3588-89ES 制造商:EXAR 制造商全稱:EXAR 功能描述:XR-T3588/89 Evaluation System
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*