- 您現在的位置：買賣IC網 > PDF目錄376462 > XRT75VL00 (Exar Corporation) E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR PDF資料下載
參數資料
| 型號： | XRT75VL00 |
| 廠商： | Exar Corporation |
| 英文描述： | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| 中文描述： | E3/DS3/STS-1線路接口單元與抖動衰減器 |
| 文件頁數： | 9/50頁 |
| 文件大?。?/td> | 268K |
| 代理商： | XRT75VL00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
XRT75VL00
REV. 1.0.3
E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
7
37
RNEG/LCV
O
Receive Negative Data Output/Line Code Violation Indicator
Function of these pins depends on whether the XRT75VL00 is configured
in Single Rail or Dual Rail mode.
If the XRT75VL00 is configured in Dual Rail mode, a negative pulse is output
through RNEG.
In Hardware mode:
Tie the pin SR/DR
(pin 22) “High” to configure the
XRT75VL00 in Single Rail mode and tie
“Low” to configure in Dual Rail mode.
In HOST mode:
XRT75VL00 can be configured in Single Rail or Dual Rail by
setting or clearing the bit in the block control register.
Line Code Violation Indicator
If the XRT75VL00 is configured in Single Rail mode then:
Whenever the Receiver Section detects a Line Code violation, it pulses this
output pin “High”. This output pin remains “Low” at all other times. It is
advisable to sample this output pin using the RxClk output signal.
11
RRING
I
Receive Ring Input
This input pin along with RTIP is used to receive the bipolar line signal from the
Remote DS3/E3/STS-1 Terminal.
12
RTIP
I
Receive TIP Input
This input pin along with RRNG is used to receive the bipolar line signal from
the Remote DS3/E3/STS-1 Terminal.
27
RxMON/
SDO
I
Receive Monitoring Mode or Serial Data Output:
In Hardware mode,
when this pin is tied “High” XRT75VL00 configures into
monitoring channel. In the monitoring mode, the Receiver is capable of monitor-
ing the signals with 20 dB flat loss plus 6 dB cable attenuation. This allows to
monitor very weak signal before declaring LOS.
In HOST Mode, XRT75VL00 can be configured to be a monitoring channel by
setting the bits in the receive control register.
N
OTE
:
If the XRT75VL00 is configured in HOST mode, this pin functions as
SDO pin (please refer to the pin description for the Microprocessor
Interface).
RECEIVE INTERFACE
P
IN
#
S
IGNAL
N
AME
T
YPE
D
ESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| XRT75VL00IV | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT79L71 | 1 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC |
| XRT79L71IB | 1 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC |
| XRT79L72 | 2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC |
| XRT79L72IB | 2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT75VL00_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75VL00D | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75VL00D_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET |
| XRT75VL00D1V-F | 制造商:Exar Corporation 功能描述: |
| XRT75VL00DES | 功能描述:時鐘合成器/抖動清除器 1CHT3/E3/STS1LIU+ DESYNC 3.3V DRV VER RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。