參數資料
型號: XRT79L72
廠商: Exar Corporation
英文描述: 2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
中文描述: 2 -通道DS3/E3自動柜員機用戶到網絡接口/ Combo IC對購買力平價
文件頁數: 10/72頁
文件大?。?/td> 441K
代理商: XRT79L72
XRT79L72
REV. P1.0.2
PRELIMINARY
2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
xr
7
P
IN
#
N
AME
TYPE
D
ESCRIPTION
GENERAL PURPOSE INPUT AND OUTPUT PINS
U3
N26
DMO
_0
DMO
_1
O
O
Drive Monitor Output Pins:
For each channel, if the DMO output signal is "High", then it means that the drive
monitor circuitry within the XRT79L72 has not detected any bipolar signals at the
MTIP and MRING inputs (or via the Internal Drive Monitor circuit) within the last
128 ± 32 bit periods. If this output signal is "Low", then it means that bipolar sig-
nals are being detected at the MTIP and MRING input pins of the XRT79L72.
W1
W2
W3
W4
GPIO_0
GPIO_1
GPIO_2
GPIO_3
I/O
General Purpose Input/Output Pins:
Each of these pins can be configured to function as either a general-purpose input
or output pin. If a given pin (GPIO_X) is configured to function as an input pin,
then the state of this input pin can be monitored by reading Bit X within the "Oper-
ation General Purpose Pin Data" Register (Address Location = 0x0147).
If a given pin is configured to function as an output pin, then the state of this out-
put pin (GPIO_X) can be controlled by writing the appropriate value into Bit X
within the "Operation General Purpose Pin Data" Register.
Finally, the user can configure a given GPIO_X pin to be an input pin by setting Bit
X, within the "Operation General Purpose Pin Direction Control Register (Address
= 0x014B) to "0". Conversely, the user can configure the GPIO_X pin to be an
output pin by setting Bit X, within the "Operation General Purpose Pin Direction
Control" Register (Address = 0x014B) to "1".
P
IN
#
N
AME
TYPE
D
ESCRIPTION
TRANSMIT SYSTEM SIDE INTERFACE PINS
AC4
NibbleIntf
I
Nibble Interface Select Input pin:
This input pin permits the user to configure the Transmit Payload Data In-
put Interface and the Receive Payload Data Output Interface blocks to
operate in either the "Serial" or the "Nibble-Parallel" Mode.
Setting this input pin "high" configures each of these blocks to operate in
the Nibble-Parallel Mode. In this mode, the "Transmit Payload Data Input
Interface" block will accept the "outbound" payload data (from the Sys-
tem-Side terminal equipment) in a "nibble-parallel" manner via the "Tx-
Nib[3:0]" input pins. Further, the Receive Payload Data Output Interface
block will output "inbound" payload data (to the System-Side terminal
equipment) in a "nibble-parallel" via the "RxNib[3:0] output pins.
Setting this input pin "low" configures each of these blocks to operate in
the Serial Mode. In this mode, the Transmit Payload Data Input Interface
block will accept the "outbound" payload data (from the System-Side ter-
minal equipment) in a "serial" manner via the "TxSer" input pin. Further,
the Receive Payload Data Output Interface block will output the "inbound"
payload data (to the System-Side terminal equipment) in a serial manner,
via the "RxSer" output pin.NOTE:
N
OTE
:
This input pin is only active if the XRT79L72 device has been configured to
operate in the Clear-Channel Framer Mode. The user is advised to tie this input
pin to GND if the user intends to configure the XRT79L72 device to operate in the
ATM UNI or PPP Modes.
相關PDF資料
PDF描述
XRT79L72IB 2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L73 3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L73IB 3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L74 4 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L74IB 4 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
相關代理商/技術參數
參數描述
XRT79L72IB 制造商:EXAR 制造商全稱:EXAR 功能描述:2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L73 制造商:EXAR 制造商全稱:EXAR 功能描述:3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L73IB 制造商:EXAR 制造商全稱:EXAR 功能描述:3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L74 制造商:EXAR 制造商全稱:EXAR 功能描述:4 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L74IB 制造商:EXAR 制造商全稱:EXAR 功能描述:4 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC