參數資料
型號： XRT79L72
廠商： Exar Corporation
英文描述： 2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
中文描述： 2 -通道DS3/E3自動柜員機用戶到網絡接口/ Combo IC對購買力平價
文件頁數： 23/72頁
文件大?。?/td> 441K
代理商： XRT79L72
xr
2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
PRELIMINARY
XRT79L72
REV. P1.0.2
20
B7
TxUSoC/
TxPSoP
I
Transmit UTOPIA - Start of Cell Input/Transmit POS-PHY - Start of Packet
Input:
The function of this input signal depends upon whether the XRT79L72 has been
configured to operate in the ATM UNI or in the PPP Mode.
ATM UNI Mode Operation - TxUSoC:
This input pin is driven by the ATM Layer Processor and is used to indicate the
start of an ATM cell that is being transmitted from the ATM Layer Processor. This
input pin must be pulsed "High" whenever the first byte (or word) of a new cell is
present on the Transmit UTOPIA Data Bus (TxUData[15:0]). This input pin must
remain "Low" at all other times.
PPP Mode Operation - TxPSoP/TxPSoC:
If the XRT79L72 has been configured to operate in the Packet-Mode, then this
input pin is pulsed "High" to denote that the first byte (or word) of a given packet
is placed on the TxPData[15:0] input pins.If the XRT79L72 has been configured
to operate in the Cell-Chunk Mode, then this input pin is pulsed "High" to denote
that the first byte of a packet chunk, if placed on the TxPData[15:0] input pins.
N
OTE
:
This input pin is only valid if the XRT79L72 has been configured to oper-
ate in the PPP Mode.
B11
TxTSX/
TxPSOF
I
Transmit - Change of Port Indicator Input/Transmit - Start of PPP
Packet (in Chunk Mode):
The exact function of this input pin depends upon whether the XRT79L72
device has been configured to operate in the Packet Mode or Cell-Chunk
Mode, as is described below.
Packet Mode - TxTSX - Transmit POS-PHY Interface - Change of
Port Indicator Output (POS-PHY Level 3, Packet Mode only):
The Link-Layer processor pulses this input pin "high" when an "in-band"
port address is present on the "TxPData[15:11]" bus input pins. When
this input pin and "TxPENB*" are both set "high" then the value of "TxP-
Data[15:11]" is the address value of the TxFIFO (Transmit POS-PHY
Port) to be selected. Subsequent write operations, into "TxPData[15:0]"
will fill the TxFIFO (within the Transmit POS-PHY Port) corresponding to
this particular "in-band" address.
Chunk Mode - TxPSOF - Receive Start of Packet Input Indicator:
The Link Layer processor pulses this input pin "high" in order to indicate
that the first byte (or 16-bit word) of a given Packet is placed on the "TxP-
Data[15:0]" pins.
N
OTE
:
This input pin is only active if the XRT79L72 device has been configured to
operate in the POS-PHY Level 3, Packet Mode or in the Chunk Mode. If the user
intends to operate the XRT79L72 device in any other mode, then he/she should
tie this input pin to GND.
A7
TxUClkO/
TxPClkO
O
Transmit UTOPIA Interface Clock/Transmit POS-PHY Interface Clock Out-
put:
This output is derived from an internal PLL.
P
IN
#
N
AME
TYPE
D
ESCRIPTION
相關PDF資料
PDF描述
XRT79L72IB 2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L73 3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L73IB 3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L74 4 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L74IB 4 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
相關代理商/技術參數
參數描述
XRT79L72IB 制造商:EXAR 制造商全稱:EXAR 功能描述:2 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L73 制造商:EXAR 制造商全稱:EXAR 功能描述:3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L73IB 制造商:EXAR 制造商全稱:EXAR 功能描述:3 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L74 制造商:EXAR 制造商全稱:EXAR 功能描述:4 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
XRT79L74IB 制造商:EXAR 制造商全稱:EXAR 功能描述:4 - CHANNEL DS3/E3 ATM UNI/PPP COMBO IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*