- 您現在的位置：買賣IC網 > PDF目錄376464 > XRT86VL3X_07 (Exar Corporation) Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 PDF資料下載
參數資料
| 型號： | XRT86VL3X_07 |
| 廠商： | Exar Corporation |
| 元件分類： | 通信及網絡 |
| 英文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 中文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 文件頁數： | 35/153頁 |
| 文件大小： | 1316K |
| 代理商： | XRT86VL3X_07 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁
XRT86VL3X
28
REV. 1.2.2
T1/E1/J1 FRAMER/LIU COMBO - ARCHITECTURE DESCRIPTION
terminal has lost framing, is only designed as a performance indicator; existing terminal out-of-frame criteria
will continue to serve as the basis for terminal alarms.
Frame-Synchronization-Bit Error Event: A frame-synchronization-bit-error event is the occurrence of a
received framing-bit-pattern not meeting the severely-errored-framing event criteria.
Line-Code Violation event: A line-code violation event is a bipolar violation of the incoming data. A line-code
violation event for an B8ZS-coded signal is the occurrence of a received excessive zeros (EXZ) or a bipolar
violation that is not part of a zero-substitution code.
Controlled Slip Event: A controlled-slip event is a replication, or deletion, of a T1 frame by the receiving
terminal. A controlled slip may occur when there is a difference between the timing of a synchronous
receiving terminal and the received signal.
3.8.4
Path and Test Signal Identification Message
The path identification message is used to identify the path between the source terminal and the sink terminal.
The test signal identification message is used by test signal generating equipment. Both identification
messages are made up of 82 bytes of data. Byte 1 to 4, 81 and 82 are the message header and bytes 5 to 80
contain six data elements. These messages use the SAPI/TEI value of 0x15 to differentiate themselves from
the performance report message.
3.8.5
Frame Structure
The message structure of message-oriented signal is shown in
Figure 33
. Two format types are shown in the
figure: format A for frames which are sending performance report message and format B for frames which
containing a path or test signal identification message. The following abbreviations are used:
SAPI: Service Access Point Identifier
C/R: Command or Response
EA: Extended Address
TEI: Terminal Endpoint Identifier
FCS: Frame Check Sequence
3.8.6
Flag Sequence
All frames shall start and end with the flag sequence consisting of one 0 bit followed by six contiguous 1 bits
and one 0 bit. The flag preceding the address field is defined as the opening flag. The flag following the Frame
Check Sequence (FCS) field is defined as the closing flag. The closing flag may also serve as the opening flag
of the next frame, in some applications. However, all receivers must be able to accommodate receipt of one or
more consecutive flags.
3.8.7
Address Field
The address field consists of two octets. A single octet address field is reserved for LAPB operation in order to
allow a single LAPB data link connection to be multiplexed along with LAPD data link connections.
3.8.8
Address Field Extension bit (EA)
The address field range is extended by reserving bit 1 of the address field octets to indicate the final octet of
the address field. The presence of a 1 in bit 1 of an address field octet signals that it is the final octet of the
address field. The double octet address field for LAPD operation shall have bit 1 of the first octet set to a 0 and
bit 1 of the second octet set to 1.
3.8.9
Command or Response bit (C/R)
The Command or Response bit identifies a frame as either a command or a response. The user side shall
send commands with the C/R bit set to 0, and responses with the C/R bit set to 1. The network side shall do the
opposite; That is, commands are sent with C/R bit set to 1, and responses are sent with C/R bit set to 0.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT86VL3X | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| XRT91L30_0611 | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| XRT91L306 | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| XRT91L30IQ | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| XRT91L30 | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT86VX38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION |
| XRT86VX38_09 | 制造商:EXAR 制造商全稱:EXAR 功能描述:8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION |
| XRT86VX38_0906 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER/LIU COMBO - HARDWARE DESCRIPTION |
| XRT86VX38IB256 | 制造商:EXAR 制造商全稱:EXAR 功能描述:8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - E1 REGISTER DESCRIPTION |
| XRT86VX38IB256ES | 功能描述:界面開發工具 Evaluation Board for XRT86VX38 256pin ICs RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。