16-BIT
參數資料
型號： XRT91L34IV
廠商： Exar Corporation
文件頁數： 18/38頁
文件大?。?/td> 0K
描述： IC MULTIRATE CDR QUAD 128LQFP
標準包裝： 72
類型： 時鐘和數據恢復（CDR），扇出緩沖器（分配），多路復用器
PLL： 是
主要目的： SONET/SDH，STS，STM
輸入： LVDS，LVPECL
輸出： LVDS，LVPECL
電路數： 1
比率 - 輸入:輸出： 1:2
差分 - 輸入:輸出： 是/是
頻率 - 最大： 622.08MHz
電源電壓： 1.71 V ~ 3.465 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-LQFP（14x14）
包裝： 托盤
XRT91L34
25
REV. 1.0.1
QUAD CHANNEL MULTIRATE STS-12/3/1 AND STM-4/1/0 SONET/SDH CDR
4.2
16-BIT SERIAL DATA INPUT DESCRITPTION
The serial data input is sampled on the rising edge of SCLK. For read operations, the SDO signal is updated
on the falling edge of SCLK. The serial data must be applied to the serial port LSB first. The 16 bits of serial
data are described below.
4.2.1
R/W (SCLK1)
The first serial bit applied to the device SDI pin determines whether a Read or Write operation is desired. If the
R/W bit is set to “0”, the serial port is configured for a Write operation. If the R/W bit is set to “1”, the serial port
is configured for a Read operation.
4.2.2
A[5:0] (SCLK2 - SCLK7)
The next 6 SCLK cycles are used to provide the address to which a Read or Write operation will occur. A0
(LSB) must be sent to the SDI pin first followed by A1 and so forth until all 6 address bits have been sampled
by SCLK.
4.2.3
X (Dummy Bit SCLK8)
The dummy bit sampled by SCLK8 is used to allow sufficient time for the serial data output pin to update data
if the readback mode is selected by setting R/W = “1”. Therefore, the state of this bit is ignored and can hold
either “0” or “1” during both Read and Write operations.
4.2.4
D[7:0] (SCLK9 - SCLK16)
The next 8 SCLK cycles are used to provide the data to be written into the internal register chosen by the ad-
dress bits. D0 (LSB) must be sent to the SDI pin first followed by D1 and so forth until all 8 data bits have been
sampled by SCLK. Once 16 SCLK cycles have been complete, the data is held until CS is pulled “High”
whereby, the serial port latches the data into the selected internal register.
4.3
8-BIT SERIAL DATA OUTPUT DESCRIPTION
When R/W is set to “1” (Read operation) the serial data output is updated on the falling edge of SCLK8 -
SCLK16, D0 (LSB) is provided at the SDO pin on the falling edge of SCLK8, followed by D1 and so forth until
all 8 data bits have been updated after which the SDO output pin returns to a high impedance state until the
next read operation.
相關PDF資料
PDF描述
MS3110P22-21P CONN RCPT 21POS WALL MNT W/PINS
M83723/78W1005N CONN PLUG 5POS STRAIGHT W/PINS
M83723/78R1005N CONN PLUG 5POS STRAIGHT W/PINS
VE-JW0-MW-B1 CONVERTER MOD DC/DC 5V 100W
VE-J1V-MW-B1 CONVERTER MOD DC/DC 5.8V 100W
相關代理商/技術參數
參數描述
XRT91L34IVF 制造商:Exar Corporation 功能描述:CDR 51.84Mbps/155.52Mbps/622.08Mbps SONET/SDH 128-Pin LQFP 制造商:EXAR 功能描述:CDR 51.84Mbps/155.52Mbps/622.08Mbps SONET/SDH 128-Pin LQFP
XRT91L34IV-F 功能描述:網絡控制器與處理器 IC 8-Bit TTL 1.8V temp -45 to 85C;UART RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT91L34IVTR 功能描述:網絡控制器與處理器 IC 4 CH OC-12/STM4 OC-3/STM1 CDR RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT91L34IVTR-F 功能描述:網絡控制器與處理器 IC 4 CH OC-12/STM4 OC-3/STM1 CDR RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT91L80 制造商:EXAR 制造商全稱:EXAR 功能描述:2.488/2.666 GBPS STS-48/STM-16 SONET/SDH TRANSCEIVER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*