XRT94L43
168
REV. 1.0.2
SONET/SDH OC-12 TO 12XDS3/E3 MAPPER
AE25
STS3TxA_CLK_2
TxSBCLK_2
DMO_2
I
TTL
STS-3 Transmit Telecom Bus Clock Input/STM-1 Sub-Rate
Clock/DMO_2 (General Purpose) input Pin:
The function of this input pin depends upon whether or not theSTS-3/
STM-1 Telecom Bus Interface for Channel 2 has been enabled.
If STS-3/STM-1 Telecom Bus (Channel 2) has been enabled -
STS-3 Transmit Telecom Bus Transmit Clock Input - Channel 2:
This input clock signal functions as the clock source for the STS-3/
STM-1 Transmit Telecom Bus, associated with Channel 2. All input
signals, (e.g., STS3TxA_ALARM_2, STS3TxA_D_2[7:0],
STS3TxA_DP_2, STS3TxA_PL_2, STS3TxA_C1J1_2) are sampled
upon the falling edge of this input clock signal.
This clock signal should operate at 19.44MHz.
If STS-3/STM-1 Telecom Bus (Channel 2) is disabled - DMO_2 -
Drive Monitor Output Input (from XRT73L0X LIU IC) - Channel 2:
This input pin can be used as a general purpose input pin.
The state of this input pin can be determined by reading the state of
Bit 2 (DMO) within the Line Interface Scan Register associated with
Channel 2 (Indirect Address = 0x3E, 0x81), (Direct Address =
0x3F81).
N
OTE
:
For Product Legacy purposes, this pin is called DMO_2
because one possible Application is to tie this input pin to a
DMO (Drive Monitor Output) output pin, from one of Exar's
XRT73L0X/XRT75L0X
DS3/E3/STS-1
However, this input pin, and the corresponding register bit
can be used for any purpose.
LIU
devices.
AD17
STS3TxA_CLK_3
TxSBCLK_3
DMO_3
I
TTL
STS-3 Transmit Telecom Bus Clock Input/STM-1 Sub-Rate
Clock/DMO_3 (General Purpose) input Pin:
The function of this input pin depends upon whether or not theSTS-3/
STM-1 Telecom Bus Interface for Channel 3 has been enabled.
If STS-3/STM-1 Telecom Bus (Channel 3) has been enabled -
STS-3 Transmit Telecom Bus Clock Input - Channel 3:
This input clock signal functions as the clock source for the STS-3/
STM-1 Transmit Telecom Bus, associated with Channel 3. All input
signals (e.g., STS3TxA_ALARM_3, STS3TxA_D_3[7:0],
STS3TxA_DP_3, STS3TxA_PL_3, STS3TxA_C1J1_3) are sampled
upon the falling edge of this input clock signal.
This clock signal should operate at 19.44MHz.
If STS-3/STM-1 Telecom Bus (Channel 3) is disabled - DMO_3
(General Purpose) Input Pin:
This input pin can be used as a general purpose input pin.
The state of this input pin can be determined by reading the state of
Bit 3 (DMO) within the Line Interface Scan Register associated with
Channel 3 (Address = 0x4E, 0x81), (Direct Address = 0x4F81).
N
OTE
:
For Product Legacy purposes, this pin is called DMO_3,
because one possible application is to tie this input pin to a
DMO (Drive Monitor Output) output pin, from one of Exar's
XRT73L0X/XRT75L0X
DS3/E3/STS-1
However, this input pin, and the corresponding register bit
can be used for any purpose.
LIU
devices.
STS-3/STM-1 TELECOM BUS INTERFACE - TRANSMIT DIRECTION
P
IN
#
S
IGNAL
N
AME
I/O
S
IGNAL
T
YPE
D
ESCRIPTION