- 您現在的位置：買賣IC網 > PDF目錄373760 > Z53C80SCSI (ZiLOG, Inc.) SMALL COMPUTER SYSTEM INTERFACE (SCSI) PDF資料下載
參數資料
| 型號： | Z53C80SCSI |
| 廠商： | ZiLOG, Inc. |
| 英文描述： | SMALL COMPUTER SYSTEM INTERFACE (SCSI) |
| 中文描述： | 小型計算機系統接口（SCSI） |
| 文件頁數： | 10/40頁 |
| 文件大?。?/td> | 447K |
| 代理商： | Z53C80SCSI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
10
Z53C80 SCSI
PS97SCC0200
Z
ILOG
FUNCTIONAL DESCRIPTION
(Continued)
Bit 0.
Arbitrate.The Arbitrate bit is set (1) to start the
Arbitration process. Prior to setting this bit, the Output Data
Register should contain the proper SCSI device ID value.
Only one data bit should be active for SCSI Bus Arbitration.
The SCSI waits for a Bus-Free condition before entering
the Arbitration phase. The results of the Arbitration phase
is determined by reading the status bits LA and AIP
(Initiator Command Register, bits 5 and 6, respectively).
Bit 1.
DMA Mode.The DMA Mode bit is normally used to
enable a DMA transfer and must be set (1) prior to writing
Start DMA Send Register, Start DMA Target Receive
Register, and Start DMA Initiator Receiver Register. These
three registers are used to start DMA transfers. The Target
Mode bit (Mode Register, bit 6) must be consistent with
writes to Start DMA Target Receive and Start DMA Initiator
Receive Registers [i.e., set (1) for a write to start DMA
Target Receive Register and set (0) for a write to Start DMA
Initiator Receive Register]. The control bit Assert Data Bus
(Initiator Command Register, bit 0) must be True (1) for all
DMA send operations. In the DMA mode, /REQ and /ACK
are automatically controlled.
The DMA Mode bit is not reset upon the receipt of an /EOP
signal. Any DMA transfer is stopped by writing a zero into
this bit location; however, care must be taken not to cause
/CS and /DACK to be active simultaneously.
Bit 2.
Monitor Busy.The Monitor Busy bit, when True (1),
causes an interrupt to be generated for an unexpected
loss of /BSY. When the interrupt is generated due to loss of
/BSY, the lower six bits of the Initiator Command Register
are reset (0) and all signals are removed from the SCSI
Bus.
Bit 3.
Enable/EOP interrupt.The enable /EOP interrupt,
when set (1), causes an interrupt to occur when the /EOP
(End of Process) signal is received from the DMA controller
logic.
Bit 4.
Enable Parity Interrupt.The Enable Parity Interrupt
bit, when set (1), will cause an interrupt (IRQ) to occur if a
parity error is detected. A parity interrupt will only be
generated if the Enable Parity Checking bit (bit 5) is also
enabled (1).
Bit 5.
Enable Parity Checking.The Enable Parity Checking
bit determines whether parity errors are ignored or saved
in the parity error latch. If this bit is reset (0), parity is
ignored. Conversely, if this bit is set (1), parity errors are
saved.
Bit 6.
Targetmode.The Targetmode bit allows the SCSI to
operate as either a SCSI Bus Initiator, bit reset (0), or as a
SCSI Bus Target device, bit set (1). If the signals /ATN and
/ACK are to be asserted on the SCSI Bus, the Targetmode
bit must be reset (0). If the signals C//D, I//O, /MSG, and
/REQ are to be asserted on the SCSI Bus, the Targetmode
bit must be set (1).
Bit 7.
0.Bit 7 should be written with a zero for proper
operation.
Target Command Register.
Address 3(Read/Write). When
connected as a target device, the Target Command
Register (Figure 11) allows the CPU to control the SCSI Bus
Information Transfer phase and/or to assert /REQ by writing
this register. The Targetmode bit (Mode Register, bit 6)
must be True (1) for bus assertion to occur. The SCSI Bus
phases are described in Table 2.
Table 2. SCSI Information Transfer Phase
Bus Phase
ASSERT
I//O
ASSERT
C//D
ASSERT
/MS
Data Out
Unspecified
Command
0
0
0
0
0
1
0
1
0
Message Out
Data In
Unspecified
0
1
1
1
0
0
1
0
1
Status
Message In
1
1
1
1
0
1
When connected as an Initiator with DMA Mode True, if the
phase lines I//O, C//D, and /MSG do not match the phase
bits in the Target Command Register, a phase mismatch
interrupt is generated when /REQ goes active. To send
data as an Initiator, the Assert I//O, Assert C//D, and Assert
/MSG bits must match the corresponding bits in the Current
SCSI Bus Status Register. The Assert /REQ bit (bit 3) has
no meaning when operating as an Initiator.
Bits 4, 5, and 6 are not used.
相關PDF資料 |
PDF描述 |
|---|---|
| Z54122 | RETRIGGERABLE MONOSTABLE MULTIVIBRATOR |
| Z5U0603 | ceramic chip capacitors |
| Z5U0805 | ceramic chip capacitors |
| Z5U1206 | ceramic chip capacitors |
| Z5U1210 | ceramic chip capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Z53E11 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:E5M Operation Manual DX CODE ZA |
| Z53RD431 | 制造商:HVCA & CKE 功能描述:Varistor, MO, 430V, 50000A, 7000pF |
| Z540 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel Atom Processor |
| Z540-TRACEABLE-W/DATA | 功能描述:手持示波器 NIST-CAL-CERT TRACEABLE W/DATA RoHS:否 制造商:Fluke 帶寬:200 MHz 采樣比:2.5 GS/s 顯示器類型:153 mm Full Color LCD 設備類型:Oscilloscopes |
| Z54122 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RETRIGGERABLE MONOSTABLE MULTIVIBRATOR |
發布緊急采購，3分鐘左右您將得到回復。