參數資料
型號： 49LF002
廠商： Silicon Storage Technology, Inc.
英文描述： 2 Mbit / 3 Mbit / 4 Mbit / 8 Mbit Firmware Hub
中文描述： 2兆位/ 3兆/ 4兆位/ 8兆固件集線器
文件頁數： 35/36頁
文件大小： 412K
代理商： 49LF002
8
Advance Information
2 Mbit / 3 Mbit / 4 Mbit / 8 Mbit Firmware Hub
SST49LF002A / SST49LF003A / SST49LF004A / SST49LF008A
2001 Silicon Storage Technology, Inc.
S71161-06-000
9/01
504
Write Lock
The Write-Lock bit, bit 0, controls the lock state described in
Table 6. The default Write status of all blocks after power-
up is write locked. When bit 0 of the Block Locking register
is set, Program and Erase operations for the corresponding
block are prevented. Clearing the Write-Lock bit will unpro-
tect the block. The Write-Lock bit must be cleared prior to
starting a Program or Erase operation since it is sampled at
the beginning of the operation.
The Write-Lock bit functions in conjunction with the hard-
ware Write Lock pin TBL# for the top Boot Block. When
TBL# is low, it overrides the software locking scheme. The
top Boot Block Locking register does not indicate the state
of the TBL# pin.
The Write-Lock bit functions in conjunction with the hard-
ware WP# pin for blocks 0 to 6. When WP# is low, it over-
rides the software locking scheme. The Block Locking
register does not indicate the state of the WP# pin.
Lock Down
The Lock-Down bit, bit 1, controls the Block Locking regis-
ter as described in Table 6. When in the FWH interface
mode, the default Lock Down status of all blocks upon
power-up is not locked down. Once the Lock-Down bit is
set, any future attempted changes to that Block Locking
register will be ignored. The Lock-Down bit is only cleared
upon a device reset with RST# or INIT# or power down.
Current Lock Down status of a particular block can be
determined by reading the corresponding Lock-Down bit.
Once a block’s Lock-Down bit is set, the Write-Lock bits for
that block can no longer be modified, and the block is
locked down in its current state of write accessibility.
JEDEC ID Registers
The JEDEC ID registers for the boot device appear at
FFBC0000H and FFBC0001H in the 4 GByte system
memory map, and will appear elsewhere if the device is not
the boot device. Register is not available for read when the
device is in Erase/Program operation. Unused register
location will read as 00H. Refer to the relevant application
note for details. See Table 7 for the device ID code.
PARALLEL PROGRAMMING MODE
Device Operation
Commands are used to initiate the memory operation func-
tions of the device. The data portion of the software com-
mand sequence is latched on the rising edge of WE#.
During the software command sequence the row address
is latched on the falling edge of R/C# and the column
address is latched on the rising edge of R/C#.
Read
The Read operation of the SST49LF00xA device is con-
trolled by OE#. OE# is the output control and is used to
gate data from the output pins. Refer to the Read cycle
timing diagram, Figure 14, for further details.
Reset
A VIL on RST# pin initiates a device reset.
Byte-Program Operation
The SST49LF00xA device is programmed on a byte-by-
byte basis. Before programming, one must ensure that the
sector, in which the byte which is being programmed exists,
is fully erased. The Byte-Program operation is initiated by
executing a four-byte command load sequence for Soft-
ware Data Protection with address (BA) and data in the last
byte sequence. During the Byte-Program operation, the
row address (A10-A0) is latched on the falling edge of R/C#
and the column Address (A21-A11) is latched on the rising
edge of R/C#. The data bus is latched in the rising edge of
WE#. The Program operation, once initiated, will be com-
pleted, within 20 s. See Figure 15 for Program operation
timing diagram, Figure 18 for timing waveforms, and Figure
26 for its flowchart. During the Program operation, the only
valid reads are Data# Polling and Toggle Bit. During the
internal Program operation, the host is free to perform addi-
tional tasks. Any commands written during the internal Pro-
gram operation will be ignored.
TABLE
6: BLOCK LOCKING REGISTER BITS
Reserved Bit [7..2]
Lock-Down Bit [1]
Write-Lock Bit [0]
Lock Status
000000
0
Full Access
000000
0
1
Write Locked (Default State at Power-Up)
000000
1
0
Locked Open (Full Access Locked Down)
000000
1
Write Locked Down
T6.3 504
相關PDF資料
PDF描述
4A000MH5 2-Input NAND Gate
4A002MH5 2-Input NOR Gate
4A004MH5 4A004MH5
4A032MH5 4A032MH5
4A08P-505-500 Surge Line Protection Module
相關代理商/技術參數
參數描述
49LV1614-90TI 制造商: 功能描述: 制造商:undefined 功能描述:
49M-011059-FX4X10 制造商:Aker Technology Company Ltd 功能描述:FX4X10 Series 11.0590MHZ 30PPM 20PF SMD Crystal
49M-027000-FX4X12 制造商:Aker Technology Company Ltd 功能描述:FX4X12 Series 27MHZ 30PPM 20PF SMD Crystal
49M-10 制造商:Honeywell Sensing and Control 功能描述:
49M1K 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*