- 您現在的位置：買賣IC網 > PDF目錄16272 > 73S1210F-EB-LITE (Maxim Integrated Products)BOARD EVAL 73S1210F LITE DOC/CBL PDF資料下載
參數資料
| 型號： | 73S1210F-EB-LITE |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 101/126頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL 73S1210F LITE DOC/CBL |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁當前第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁
73S1210F Data Sheet
DS_1210F_001
76
Rev. 1.4
Special Notes Regarding Synchronous Mode Operation
When the SCISYN or SCESNC bits (SPrtcol, bit 7, bit 5, respectively) are set, the selected smart card
interface operates in synchronous mode and there are changes in the definition and behavior of pertinent
register bits and associated circuitry. The following requirements are to be noted:
1.
The source for the smart card clock (CLK or SCLK) is the ETU counter. Only the actively selected
interface can have a running synchronous clock. In contrast, an unselected interface may have a
running clock in the asynchronous mode of operation.
2.
The control bits CLKLVL, SCLKLVL, CLKOFF, and SCLKOFF are functional in synchronous mode.
When the CLKOFF bit is set, it will not truncate either the logic low or logic high period when the (stop
at) level is of opposite polarity. The CLK/SCLK signal will complete a correct logic low or logic high
duty cycle before stopping at the selected level. The CLK “start” is a result of the falling edge of the
CLKOFF bit. Setting clock to run when it is stopped low will result in a half period of low before going
high. Setting clock to run when it is stopped high will result in the clock going low immediately and
then running at the selected rate with 50% duty cycle (within the limitations of the ETU divisor value).
3.
The Rlen(7:0) is configured to count the falling edges of the ETU clock (CLK or SCLK) after it has
been loaded with a value from 1 to 255. A value of 0 disables the counting function and RLen
functions such as I/O source selection (I/O signal bypasses the FIFOs and is controlled by the
SCCLK/SCECLK SFRs). When the RLen counter reaches the “max” (loaded) value, it sets the
order to start the counting/clocking process again. This allows the processor to select the number of
CLK cycles and hence, the number of bits to be read or written to/from the card.
4.
The FIFO is not clocked by the first CLK (falling) edge resulting from a CLKOFF de-assertion (a clock
start event) when the CLK was stopped in the high state and RLen has been loaded but not yet
clocked.
5.
The state of the pin IO or SIO is sampled on the rising edge of CLK/SCLK and stored in bit 5 of the
6.
When Rlen = max or 0 and I2CMODE= 1 (STXCtl, b7), the IO or SIO signal is directly controlled by the
data and direction bits in the respective SCCtl and SCECtl register. The state of the data in the TX
FIFO is bypassed.
7.
In the SPrtcol register, bit 6 (MODE9/8B) becomes active. When set, the RXData FIFO will read
nine-bit words with the state of the ninth bit being readable in SRXCtl, bit 7 (B9DAT). The RXDAV
interrupt will occur when the ninth bit has been clocked in (rising edge of CLK or SCLK).
8.
Care must be taken to clear the RX and TX FIFOs at the start of any transaction. The user shall read
the RX FIFO until it indicates empty status. Reading the TX FIFO twice will reset the input byte
pointer and the next write to the TX FIFO will load the byte to the “first out” position. Note that the bit
pointer (serializer/deserializer) is reset to bit 0 on any change of the TX/RXD bit.
Special bits that are only active for sync mode include: SRXCtl, b7 “BIT9DAT”, SPrtcol, b6 “MODE9/8B”,
STXCtl, b7 “I2CMODE”, and the definition of SCInt, b7, which was “WAITTO”, becomes RLenINT interrupt,
and SCIE, b7, which was “WTOIEN”, becomes RLenIEN.
相關PDF資料 |
PDF描述 |
|---|---|
| CM453232-4R7JL | INDUCTOR 4.7UH 315MA SMD |
| GBM18DRYF | CONN EDGECARD 36POS DIP .156 SLD |
| A3DDH-3036M | IDC CABLE - AKR30H/AE30M/AKR30H |
| VI-2WT-EY-S | CONVERTER MOD DC/DC 6.5V 50W |
| CM453232-471JL | INDUCTOR 470UH 62MA SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S1210F-EB-LiteMS | 功能描述:開發板和工具包 - 8051 73S1210F Eval Brd Lite + Multi Sam RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| 73S1215F | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:80515 System-on-Chip with USB, ISO 7816 / EMV, PINpad and More |
| 73S1215F-44IM/F | 功能描述:8位微控制器 -MCU 80515 SoC w/USB & PINpad RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| 73S1215F-44IM/F/P | 功能描述:IC SMART CARD READER PROG 44-QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:73S12xx 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
| 73S1215F-44IMR/F | 功能描述:8位微控制器 -MCU 80515 SoC w/USB & PINpad RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。