參數資料
型號： AD9629BCPZRL7-80
廠商： Analog Devices Inc
文件頁數： 17/32頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 80MSPS 32LFCSP
標準包裝： 1,500
位數： 12
采樣率（每秒）： 80M
數據接口： 串行，SPI?
轉換器數目： 1
功率耗散（最大）： 100mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤，CSP
供應商設備封裝： 32-LFCSP-VQ
包裝： 帶卷 (TR)
輸入數目和類型： 2 個單端，單極；1 個差分，單極
AD9629
Rev. 0 | Page 24 of 32
SERIAL PORT INTERFACE (SPI)
The AD9629 serial port interface (SPI) allows the user to configure
the converter for specific functions or operations through a
structured register space provided inside the ADC. The SPI
gives the user added flexibility and customization, depending
on the application. Addresses are accessed via the serial port
and can be written to or read from via the port. Memory is
organized into bytes that can be further divided into fields,
which are documented in the Memory Map section. For
detailed operational information, see the AN-877 Application
Note, Interfacing to High Speed ADCs via SPI.
CONFIGURATION USING THE SPI
Three pins define the SPI of this ADC: the SCLK, the SDIO,
and the CSB (see Table 13). The SCLK (a serial clock) is used
to synchronize the read and write data presented from and to
the ADC. The SDIO (serial data input/output) is a dual-purpose
pin that allows data to be sent and read from the internal ADC
memory map registers. The CSB (chip select bar) is an active-
low control that enables or disables the read and write cycles.
Table 13. Serial Port Interface Pins
Pin
Function
SCLK
Serial clock. The serial shift clock input, which is used to
synchronize serial interface reads and writes.
SDIO
Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
CSB
Chip select bar. An active-low control that gates the read
and write cycles.
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing. An example of the
serial timing and its definitions can be found in Figure 54 and
Other modes involving the CSB are available. The CSB can be
held low indefinitely, which permanently enables the device;
this is called streaming. The CSB can stall high between bytes to
allow for additional external timing. When CSB is tied high, SPI
functions are placed in high impedance mode. This mode turns
on any SPI pin secondary functions.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits as shown in Figure 54.
All data is composed of 8-bit words. The first bit of the first byte in
a multibyte serial data transfer frame indicates whether a read
command or a write command is issued. This allows the serial
data input/output (SDIO) pin to change direction from an input
to an output at the appropriate point in the serial frame.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an output
at the appropriate point in the serial frame.
Data can be sent in MSB-first mode or in LSB-first mode. MSB
first is the default on power-up and can be changed via the SPI
port configuration register. For more information about this
and other features, see the AN-877 Application Note, Interfacing
to High Speed ADCs via SPI.
DON’T CARE
SDIO
SCLK
CSB
tS
tDH
tCLK
tDS
tH
tHIGH
tLOW
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
0854
0-
023
Figure 54. Serial Port Interface Timing Diagram
相關PDF資料
PDF描述
MS27474T20B41PC CONN RCPT 41POS JAM NUT W/PINS
MS27484T12F4P CONN PLUG 4POS STRAIGHT W/PINS
MS3106F16-13P CONN PLUG 2POS STRAIGHT W/PINS
MS3102E22-12P CONN RCPT 5POS BOX MNT W/PINS
MS3106E16-13P CONN PLUG 2POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
AD9629XCPZ-40 功能描述:IC ADC 12BIT 40MSPS 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1
AD9630 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Distortion 750 MHz Closed-Loop Buffer Amp
AD9630AN 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Distortion 750 MHz Closed-Loop Buffer Amp
AD9630AR 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Distortion 750 MHz Closed-Loop Buffer Amp
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*