- 您現在的位置：買賣IC網 > PDF目錄10155 > AD9629BCPZRL7-80 (Analog Devices Inc)IC ADC 12BIT 80MSPS 32LFCSP PDF資料下載
參數資料
| 型號： | AD9629BCPZRL7-80 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 80MSPS 32LFCSP |
| 標準包裝： | 1,500 |
| 位數： | 12 |
| 采樣率（每秒）： | 80M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 100mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，單極；1 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD9629
Rev. 0 | Page 30 of 32
APPLICATIONS INFORMATION
DESIGN GUIDELINES
Before starting design and layout of the AD9629 as a system,
it is recommended that the designer become familiar with these
guidelines, which discuss the special circuit connections and
layout requirements needed for certain pins.
Power and Ground Recommendations
When connecting power to the AD9629, it is strongly recom-
mended that two separate supplies be used. Use one 1.8 V supply
for analog (AVDD); use a separate 1.8 V to 3.3 V supply for the
digital output supply (DRVDD). If a common 1.8 V AVDD and
DRVDD supply must be used, the AVDD and DRVDD domains
must be isolated with a ferrite bead or filter choke and separate
decoupling capacitors. Several different decoupling capacitors
can be used to cover both high and low frequencies. Locate
these capacitors close to the point of entry at the PCB level
and close to the pins of the part, with minimal trace length.
A single PCB ground plane should be sufficient when using the
AD9629. With proper decoupling and smart partitioning of the
PCB analog, digital, and clock sections, optimum performance
is easily achieved.
Exposed Paddle Thermal Heat Sink Recommendations
The exposed paddle (Pin 0) is the only ground connection for
the AD9629; therefore, it must be connected to analog ground
(AGND) on the customer’s PCB. To achieve the best electrical
and thermal performance, mate an exposed (no solder mask)
continuous copper plane on the PCB to the AD9629 exposed
paddle, Pin 0.
The copper plane should have several vias to achieve the
lowest possible resistive thermal path for heat dissipation to
flow through the bottom of the PCB. Fill or plug these vias
with nonconductive epoxy.
To maximize the coverage and adhesion between the ADC and
the PCB, a silkscreen should be overlaid to partition the continuous
plane on the PCB into several uniform sections. This provides
several tie points between the ADC and the PCB during the reflow
process. Using one continuous plane with no partitions guarantees
only one tie point between the ADC and the PCB. For detailed
information about packaging and PCB layout of chip scale
packages, see the AN-772 Application Note, A Design and
Manufacturing Guide for the Lead Frame Chip Scale Package
(LFCSP), at www.analog.com.
Encode Clock
For optimum dynamic performance a low jitter encode clock
source with a 50% duty cycle ±5% should be used to clock the
AD9629.
VCM
The VCM pin should be decoupled to ground with a 0.1 μF
capacitor, as shown in Figure 38.
RBIAS
The AD9629 requires that a 10 kΩ resistor be placed between
the RBIAS pin and ground. This resistor sets the master current
reference of the ADC core and should have at least a 1% tolerance.
Reference Decoupling
Externally decouple the VREF pin to ground with a low ESR,
1.0 μF capacitor in parallel with a low ESR, 0.1 μF ceramic
capacitor.
SPI Port
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CSB, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices,
it may be necessary to provide buffers between this bus and the
AD9629 to keep these signals from transitioning at the converter
inputs during critical sampling periods.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27474T20B41PC | CONN RCPT 41POS JAM NUT W/PINS |
| MS27484T12F4P | CONN PLUG 4POS STRAIGHT W/PINS |
| MS3106F16-13P | CONN PLUG 2POS STRAIGHT W/PINS |
| MS3102E22-12P | CONN RCPT 5POS BOX MNT W/PINS |
| MS3106E16-13P | CONN PLUG 2POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9629XCPZ-40 | 功能描述:IC ADC 12BIT 40MSPS 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1 |
| AD9630 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Distortion 750 MHz Closed-Loop Buffer Amp |
| AD9630AN | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Distortion 750 MHz Closed-Loop Buffer Amp |
| AD9630AR | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Distortion 750 MHz Closed-Loop Buffer Amp |
發布緊急采購，3分鐘左右您將得到回復。