參數資料
型號： AD9641-155KITZ
廠商： Analog Devices Inc
文件頁數： 20/36頁
文件大?。?/td> 0K
描述： KIT EVAL FOR AD9641
設計資源： AD9641 Gerber Files
標準包裝： 1
系列： *
Data Sheet
AD9641
Rev. B | Page 27 of 36
SERIAL PORT INTERFACE (SPI)
The AD9641 serial port interface (SPI) allows the user to configure
the converter for specific functions or operations through a
structured register space provided inside the ADC. The SPI
gives the user added flexibility and customization, depending on
the application. Addresses are accessed via the serial port and
can be written to or read from via the port. Memory is organized
into bytes that can be further divided into fields, which are docu-
mented in the Memory Map section. For detailed operational
information, see the AN-877 Application Note, Interfacing to
High Speed ADCs via SPI.
CONFIGURATION USING THE SPI
Three pins define the SPI of this ADC: the SCLK pin, the SDIO
pin, and the CSB pin (see Table 15). The SCLK (a serial clock) is
used to synchronize the read and write data presented from and
to the ADC. The SDIO (serial data input/output) is a dual-purpose
pin that allows data to be sent to and read from the internal ADC
memory map registers. The CSB (chip select bar) is an active-
low control that enables or disables the read and write cycles.
Table 15. Serial Port Interface Pins
Pin
Function
SCLK
Serial clock. The serial shift clock input, which is used to
synchronize serial interface reads and writes.
SDIO
Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
CSB
Chip select bar. An active-low control that gates the read
and write cycles.
The falling edge of the CSB, in conjunction with the rising edge
of the SCLK, determines the start of the framing. An example of
the serial timing and its definitions can be found in Figure 70
Other modes involving the CSB are available. The CSB can be
held low indefinitely, which permanently enables the device;
this is called streaming. The CSB can stall high between bytes to
allow for additional external timing. When CSB is tied high, SPI
functions are placed in high impedance mode.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. The first bit of the first byte in
a multibyte serial data transfer frame indicates whether a read
command or a write command is issued. If the instruction is
a readback operation, performing a readback causes the serial
data input/output (SDIO) pin to change direction from an input
to an output at the appropriate point in the serial frame.
All data is composed of 8-bit words. Data can be sent in MSB-
first mode or in LSB-first mode. MSB first is the default on
power-up and can be changed via the SPI port configuration
register. For more information about this and other features,
see the AN-877 Application Note, Interfacing to High Speed
ADCs via SPI.
DON’T CARE
SDIO
SCLK
CSB
tS
tDH
tCLK
tDS
tH
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
tLOW
tHIGH
09
21
0-
04
9
Figure 70. Serial Port Interface Timing Diagram
相關PDF資料
PDF描述
380LX121M400J012 CAP ALUM 120UF 400V 20% SNAP
DS9097U-S09# COM PORT ADAPTER
VI-2W0-EY CONVERTER MOD DC/DC 5V 50W
381LX101M450J022 CAP ALUM 100UF 450V 20% SNAP
VI-21H-EY CONVERTER MOD DC/DC 52V 50W
相關代理商/技術參數
參數描述
AD9641-80KITZ 功能描述:BOARD EVAL FOR AD9641 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
AD9641BCPZ-155 制造商:Analog Devices 功能描述:14BIT 155MSPS ADC W/JESD204A - Trays 制造商:Analog Devices 功能描述:IC ADC 14BIT SRL 155MSPS 32LFCSP
AD9641BCPZ-80 功能描述:IC ADC 14BIT SRL 80MSPS 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD9641BCPZRL7-155 制造商:Analog Devices 功能描述:14BIT 155MSPS ADC W/JESD204A - Tape and Reel 制造商:Analog Devices 功能描述:IC ADC 14BIT SRL 155MSPS 32LFCSP
AD9641BCPZRL7-80 功能描述:14 Bit Analog to Digital Converter 1 Input 1 Pipelined 32-LFCSP-WQ (5x5) 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:有效 位數:14 采樣率（每秒）:80M 輸入數:1 輸入類型:差分 數據接口:JESD204A 配置:S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:1 架構:管線 參考類型:內部 電壓 - 電源，模擬:1.7 V ~ 1.9 V 電壓 - 電源，數字:1.7 V ~ 1.9 V 特性:- 工作溫度:-40°C ~ 85°C 封裝/外殼:32-WFQFN 裸露焊盤，CSP 供應商器件封裝:32-LFCSP-WQ（5x5） 標準包裝:1,500
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*