參數資料
型號: ADSP-21065LKSZ-240
廠商: Analog Devices Inc
文件頁數: 9/44頁
文件大?。?/td> 0K
描述: IC DSP CONTROLLR 544KBIT 208MQFP
產品培訓模塊: SHARC Processor Overview
標準包裝: 1
系列: SHARC®
類型: 浮點
接口: 主機接口,串行端口
時鐘速率: 60MHz
非易失內存: 外部
芯片上RAM: 64kB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 3.30V
工作溫度: 0°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 208-BFQFP
供應商設備封裝: 208-MQFP(28x28)
包裝: 托盤
其它名稱: ADSP-21065LKSZ240
ADSP-21065LKSZ240-ND
REV. C
ADSP-21065L
–17–
Memory Write—Bus Master
Use these specifications for asynchronous interfacing to memories (and memory-mapped peripherals) without reference to CLKIN.
These specifications apply when the ADSP-21065L is the bus master when accessing external memory space. These switching
characteristics also apply for bus master synchronous read/write timing (see Synchronous Read/Write—Bus Master below). If these
timing requirements are met, the synchronous read/write timing can be ignored (and vice versa). An exception to this is the ACK pin
timing requirements as described in the note below.
Parameter
Min
Max
Unit
Timing Requirements:
tDAAK
ACK Delay from Address
1, 2
24.0 + 30 DT + W
ns
tDSAK
ACK Delay from
WR Low1
19.5 + 24 DT + W
ns
Switching Characteristics:
tDAWH
Address, Selects to
WR Deasserted2
29.0 + 31 DT + W
ns
tDAWL
Address, Selects to
WR Low2
3.5 + 6 DT
ns
tWW
WR Pulsewidth
24.5 + 25 DT + W
ns
tDDWH
Data Setup Before
WR High
15.5 + 19 DT + W
ns
tDWHA
Address Hold After
WR Deasserted
0.0 + 1 DT + H
ns
tDATRWH
Data Disable After
WR Deasserted3
1.0 + 1 DT + H
4.0 + 1 DT + H
ns
tWWR
WR High to WR, RD Low
4.5 + 7 DT + H
ns
tWRDGL
WR High to DMAGx Low
11.0 + 13 DT + H
ns
tDDWR
Data Disable Before
WR or RD Low
3.5 + 6 DT + I
ns
tWDE
WR Low to Data Enabled
4.5 + 6 DT
ns
W = (number of wait states specified in WAIT register)
tCK.
H = tCK (if an address hold cycle occurs, as specified in WAIT register; otherwise H = 0).
I = tCK (if a bus idle cycle occurs, as specified in WAIT register; otherwise I = 0).
NOTES
1ACK is not sampled on external memory accesses that use the Internal wait state mode. For the first CLKIN cycle of a new external memory access, ACK must be
valid by tDAAK or tDSAK or synchronous specification tSACKC for wait state modes External, Either, or Both (Both, if the internal wait state is zero). For the second and
subsequent cycles of a wait stated external memory access, synchronous specifications t SACKC and tHACKC must be met for wait state modes External, Either, or Both
(Both, after internal wait states have completed).
2The falling edge of
MSx, SW, and BMS is referenced.
3See System Hold Time Calculation under Test Conditions for calculation of hold times given capacitive and dc loads.
RD
ACK
DATA
WR
ADDRESS
MSx , SW
BMS
tDAWL
tWW
tDAAK
tWWR
tWDE
tDDWR
tDWHA
tDDWH
tDAWH
tDSAK
DMAG
tDATRWH
tWRDGL
Figure 12. Memory Write—Bus Master
相關PDF資料
PDF描述
GEC07DRTI CONN EDGECARD 14POS DIP .100 SLD
TAP106M035DCS CAP TANT 10UF 35V 20% RADIAL
HMM36DRTF CONN EDGECARD 72POS DIP .156 SLD
VI-B12-CW-B1 CONVERTER MOD DC/DC 15V 100W
VE-21K-CY-F3 CONVERTER MOD DC/DC 40V 50W
相關代理商/技術參數
參數描述
ADSP-21065LKSZ-264 功能描述:IC DSP CONTROLL 544KBIT 208-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:SHARC® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C,McASP,McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA,F(xiàn)CBGA 供應商設備封裝:548-FCBGA(27x27) 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-2106X 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer Family
ADSP-2109 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost DSP Microcomputers
ADSP-2109KP-80 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost DSP Microcomputers
ADSP-2109LKP-55 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost DSP Microcomputers