參數資料
型號： ADSP-21478KCPZ-1A
廠商： Analog Devices Inc
文件頁數： 11/76頁
文件大?。?/td> 0K
描述： IC DSP SHARK 200MHZ 88LFCSP
標準包裝： 1
系列： SHARC®
類型： 浮點
接口： DAI，DPI，EBI/EMI，I²C，SPI，SPORT，UART/USART
時鐘速率： 200MHz
非易失內存： ROM（4Mb）
芯片上RAM： 3Mb
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.20V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 88-VFQFN 裸露焊盤，CSP
供應商設備封裝： 88-LFCSP-VQ（12x12）
包裝： 托盤
Rev. C
|
Page 19 of 76
|
July 2013
TDI
I (ipu)
Test Data Input (JTAG). Provides serial data for the boundary scan logic.
TDO
O/T
High-Z
Test Data Output (JTAG). Serial scan output of the boundary scan path.
TMS
I (ipu)
Test Mode Select (JTAG). Used to control the test state machine.
TCK
I
Test Clock (JTAG). Provides a clock for JTAG boundary scan. TCK must be asserted
(pulsed low) after power-up or held low for proper operation of the device.
TRST
I (ipu)
Test Reset (JTAG). Resets the test state machine. TRST must be asserted (pulsed
low) after power-up or held low for proper operation of the processor.
EMU
O (O/D, ipu)
High-Z
Emulation Status. Must be connected to the Analog Devices DSP Tools product
line of JTAG emulators target board connector only.
CLK_CFG1–0
I
Core to CLKIN Ratio Control. These pins set the startup clock frequency.
Note that the operating frequency can be changed by programming the PLL
multiplier and divider in the PMCTL register at any time after the core comes out
of reset. The allowed values are:
00 = 8:1
01 = 32:1
10 = 16:1
11 = reserved
CLKIN
I
Local Clock In. Used in conjunction with XTAL. CLKIN is the clock input. It
configures the processors to use either its internal clock generator or an external
clock source. Connecting the necessary components to CLKIN and XTAL enables
the internal clock generator. Connecting the external clock to CLKIN while leaving
XTAL unconnected configures the processors to use the external clock source
such as an external clock oscillator. CLKIN may not be halted, changed, or
operated below the specified frequency.
XTAL
O
Crystal Oscillator Terminal. Used in conjunction with CLKIN to drive an external
crystal.
RESET
I
Processor Reset. Resets the processor to a known state. Upon deassertion, there
is a 4096 CLKIN cycle latency for the PLL to lock. After this time, the core begins
program execution from the hardware reset vector address. The RESET input must
be asserted (low) at power-up.
RESETOUT/RUNRSTIN I/O (ipu)
Reset Out/Running Reset In. The default setting on this pin is reset out. This pin
also has a second function as RUNRSTIN which is enabled by setting bit 0 of the
RUNRSTCTL register. For more information, see the ADSP-214xx SHARC Processor
Hardware Reference.
BOOT_CFG2–0
I
Boot Configuration Select. These pins select the boot mode for the processor.
The BOOT_CFG pins must be valid before RESET (hardware and software) is de-
asserted.
The BOOT_CFG2 pin is only available on the 196-lead package.
Table 11. Pin Descriptions (Continued)
Name
Type
State During/
After Reset
Description
The following symbols appear in the Type column of Table 11: A = asynchronous, I =input, O = output, S = synchronous, A/D = active drive,
O/D = open drain, and T = three-state, ipd = internal pull-down resistor, ipu = internal pull-up resistor.
The internal pull-up (ipu) and internal pull-down (ipd) resistors are designed to hold the internal path from the pins at the expected logic
levels. To pull-up or pull-down the external pads to the expected logic levels, use external resistors. Internal pull-up/pull-down resistors
cannot be enabled/disabled and the value of these resistors cannot be programmed. The range of an ipu resistor can be 26 kΩ to 63 kΩ. The
range of an ipd resistor can be 31 kΩ to 85 kΩ. The three-state voltage of ipu pads will not reach to full the VDD_EXT level; at typical conditions
the voltage is in the range of 2.3 V to 2.7 V.
In this table, all pins are LVTTL compliant with the exception of the thermal diode, shift register, and real-time clock (RTC) pins.
Not all pins are available in the 88-lead LFCSP_VQ and 100-lead LQFP package. For more information, see Table 2 on Page 3 and Table 62 on
Page 70.
相關PDF資料
PDF描述
VI-22M-CY-F3 CONVERTER MOD DC/DC 10V 50W
5703-RC CHOKE RF HI CURR 125UH 15% RAD
VI-22L-CY-F4 CONVERTER MOD DC/DC 28V 50W
EBM08DRXH CONN EDGECARD 16POS DIP .156 SLD
RS-4815D CONV DC/DC 2W 36-72VIN +/-15VOUT
相關代理商/技術參數
參數描述
ADSP-21478KSWZ-1A 功能描述:IC DSP SHARC 200MHZ LP 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21478KSWZ-2A 功能描述:IC DSP SHARC 266MHZ LP 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21478KSWZ-ENG 制造商:Analog Devices 功能描述:SHARC PROCESSOR - Trays
ADSP-21479 制造商:AD 制造商全稱:Analog Devices 功能描述:SHARC Processor
ADSP-21479BBCZ-2A 功能描述:IC DSP SHARC 266MHZ LP 196CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*