- 您現在的位置：買賣IC網 > PDF目錄19467 > ADSP-2188MBSTZ-266 (Analog Devices Inc)IC DSP CONTROLLER 16BIT 100LQFP PDF資料下載
參數資料
| 型號： | ADSP-2188MBSTZ-266 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP CONTROLLER 16BIT 100LQFP |
| 標準包裝： | 1 |
| 系列： | ADSP-21xx |
| 類型： | 定點 |
| 接口： | 主機接口，串行端口 |
| 時鐘速率： | 66MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 256kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 2.50V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
REV. 0
–14–
ADSP-2188M
I/O Space (Full Memory Mode)
The ADSP-2188M supports an additional external memory
space called I/O space. This space is designed to support simple
connections to peripherals (such as data converters and external
registers) or to bus interface ASIC data registers. I/O space sup-
ports 2048 locations of 16-bit wide data. The lower eleven bits
of the external address bus are used; the upper three bits are
undefined. Two instructions were added to the core ADSP-2100
Family instruction set to read from and write to I/O memory
space. The I/O space also has four dedicated three-bit wait state
registers, IOWAIT0–3, which in combination with the wait state
mode bit, specify up to 15 wait states to be automatically gener-
ated for each of four regions. The wait states act on address
ranges as shown in Table V.
Table V. Wait States
Address Range
Wait State Register
0x000–0x1FF
IOWAIT0 and Wait State Mode Select Bit
0x200–0x3FF
IOWAIT1 and Wait State Mode Select Bit
0x400–0x5FF
IOWAIT2 and Wait State Mode Select Bit
0x600–0x7FF
IOWAIT3 and Wait State Mode Select Bit
Composite Memory Select (
CMS)
The ADSP-2188M has a programmable memory select signal that
is useful for generating memory select signals for memories
mapped to more than one space. The
CMS signal is gener-
ated to have the same timing as each of the individual memory
select signals (
PMS, DMS, BMS, IOMS) but can combine their
functionality.
Each bit in the CMSSEL register, when set, causes the
CMS
signal to be asserted when the selected memory select is
asserted. For example, to use a 32K word memory to act as both
program and data memory, set the
PMS and DMS bits in the
CMSSEL register and use the
CMS pin to drive the chip
select of the memory, and use either
DMS or PMS as the
additional address bit.
The
CMS pin functions like the other memory select signals
with the same timing and bus request logic. A 1 in the enable bit
causes the assertion of the
CMS signal at the same time as the
selected memory select signal. All enable bits default to 1 at reset,
except the
BMS bit.
Byte Memory Select (
BMS)
The ADSP-2188M’s
BMS disable feature combined with the
CMS pin allows use of multiple memories in the byte memory
space. For example, an EPROM could be attached to the
BMS
select, and an SRAM could be connected to
CMS. Because at
reset
BMS is enabled, the EPROM would be used for booting.
After booting, software could disable
BMS and set the CMS
signal to respond to
BMS, enabling the SRAM.
Byte Memory
The byte memory space is a bidirectional, 8-bit-wide, external
memory space used to store programs and data. Byte memory is
accessed using the BDMA feature. The byte memory space con-
sists of 256 pages, each of which is 16K
× 8.
The byte memory space on the ADSP-2188M supports read and
write operations as well as four different data formats. The byte
memory uses data bits 15:8 for data. The byte memory uses data
bits 23:16 and address bits 13:0 to create a 22-bit address. This
allows up to a 4 meg
× 8 (32 megabit) ROM or RAM to be used
without glue logic. All byte memory accesses are timed by the
BMWAIT register and the wait state mode bit.
Byte Memory DMA (BDMA, Full Memory Mode)
The byte memory DMA controller allows loading and storing of
program instructions and data using the byte memory space. The
BDMA circuit is able to access the byte memory space while the
processor is operating normally and steals only one DSP cycle
per 8-, 16- or 24-bit word transferred.
BDMA CONTROL
BMPAGE
BTYPE
BDIR
0 = LOAD FROM BM
1 = STORE TO BM
BCR
0 = RUN DURING BDMA
1 = HALT DURING BDMA
00
0
00
000
0
1
0
15 14 13 12 11 10
9
8
7
6
5
43210
DM (0x3FE3)
BDMA
OVERLAY
BITS
Figure 9. BDMA Control Register
The BDMA circuit supports four different data formats that are
selected by the BTYPE register field. The appropriate number
of 8-bit accesses are done from the byte memory space to build
the word size selected. Table VI shows the data formats sup-
ported by the BDMA circuit.
Table VI. Data Formats
BTYPE
Internal Memory Space Word Size Alignment
00
Program Memory
24
Full Word
01
Data Memory
16
Full Word
10
Data Memory
8
MSBs
11
Data Memory
8
LSBs
Unused bits in the 8-bit data memory formats are filled with 0s.
The BIAD register field is used to specify the starting address
for the on-chip memory involved with the transfer. The 14-bit
BEAD register specifies the starting address for the external byte
memory space. The 8-bit BMPAGE register specifies the start-
ing page for the external byte memory space. The BDIR register
field selects the direction of the transfer. Finally, the 14-bit
BWCOUNT register specifies the number of DSP words to
transfer and initiates the BDMA circuit transfers.
BDMA accesses can cross page boundaries during sequential
addressing. A BDMA interrupt is generated on the completion
of the number of transfers specified by the BWCOUNT register.
The BWCOUNT register is updated after each transfer so it can
be used to check the status of the transfers. When it reaches zero,
the transfers have finished and a BDMA interrupt is generated.
The BMPAGE and BEAD registers must not be accessed by the
DSP during BDMA operations.
The source or destination of a BDMA transfer will always be
on-chip program or data memory.
相關PDF資料 |
PDF描述 |
|---|---|
| TAJB105K035H | CAP TANT 1UF 35V 10% 1210 |
| MAX31855EASA+ | IC CONV THERMOCOUPLE-DGTL 8SOIC |
| GCC05DRXN | CONN EDGECARD 10POS DIP .100 SLD |
| VE-B1N-CX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
| VE-21W-CY-F3 | CONVERTER MOD DC/DC 5.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2188MKCA-300 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 75MHz 75MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:48K/56K 16-BIT DSP 2.5V 75 MIPS MINI-BGA - Bulk |
| ADSP-2188MKST-300 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 75MHz 75MIPS 100-Pin LQFP |
| ADSP-2188MKSTZ-300 | 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-2188N | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
| ADSP2188N WAFER | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。