參數資料
型號： ADSP-2189MKSTZ-300
廠商： Analog Devices Inc
文件頁數： 30/32頁
文件大小： 0K
描述： IC DSP CONTROLLER 16BIT 100-LQFP
標準包裝： 1
系列： ADSP-21xx
類型： 定點
接口： 主機接口，串行端口
時鐘速率： 75MHz
非易失內存： 外部
芯片上RAM： 192kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 2.50V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
其它名稱： ADSP-2189MKSTZ300
ADSP-2189MKSTZ300-ND
REV. A
ADSP-2189M
–7–
The master reset sets all internal stack pointers to the empty
stack condition, masks all interrupts and clears the MSTAT
register. When
RESET is released, if there is no pending bus
request and the chip is configured for booting, the boot-loading
sequence is performed. The first instruction is fetched from
on-chip program memory location 0x0000 once boot loading
completes.
Power Supplies
The ADSP-2189M has separate power supply connections for
the internal (VDDINT) and external (VDDEXT) power supplies.
The internal supply must meet the 2.5 V requirement. The
external supply can be connected to either a 2.5 V or 3.3 V
supply. All external supply pins must be connected to the same
supply. All input and I/O pins can tolerate input voltages up
to 3.6 V regardless of the external supply voltage. This fea-
ture provides maximum flexibility in mixing 2.5 V and 3.3 V
components.
MODES OF OPERATION
Setting Memory Mode
Memory Mode selection for the ADSP-2189M is made during
chip reset through the use of the Mode C pin. This pin is multi-
plexed with the DSP’s PF2 pin, so care must be taken in how
the mode selection is made. The two methods for selecting the
value of Mode C are active and passive.
Table II. ADSP-2189M Modes of Operation
MODE D
MODE C
MODE B
MODE A
Booting Method
X
0
BDMA feature is used to load the first 32 program memory words from the
byte memory space. Program execution is held off until all 32 words have
been loaded. Chip is configured in Full Memory Mode.
1
X
010No automatic boot operations occur. Program execution starts at external
memory location 0. Chip is configured in Full Memory Mode. BDMA can
still be used but the processor does not automatically use or wait for these
operations.
0100
BDMA feature is used to load the first 32 program memory words from the
byte memory space. Program execution is held off until all 32 words have
been loaded. Chip is configured in Host Mode.
IACK has active pull-down.
(REQUIRES ADDITIONAL HARDWARE).
0101IDMA feature is used to load any internal memory as desired. Program ex-
ecution is held off until internal program memory location 0 is written to.
Chip is configured in Host Mode.
IACK has active pull-down.1
1100
BDMA feature is used to load the first 32 program memory words from the
byte memory space. Program execution is held off until all 32 words have
been loaded. Chip is configured in Host Mode;
IACK requires external pull-
down. (REQUIRES ADDITIONAL HARDWARE).
1101IDMA feature is used to load any internal memory as desired. Program ex-
ecution is held off until internal program memory location 0 is written to.
Chip is configured in Host Mode.
IACK requires external pull-down.1
NOTE
1Considered as standard operating settings. Using these configurations allows for easier design and better memory management.
Passive Configuration involves the use a pull-up or pull-down
resistor connected to the Mode C pin. To minimize power
consumption, or if the PF2 pin is to be used as an output in the
DSP application, a weak pull-up or pull-down, on the order of
10 k
, can be used. This value should be sufficient to pull the
pin to the desired level and still allow the pin to operate as a
programmable flag output without undue strain on the processor’s
output driver. For minimum power consumption during power-
down, reconfigure PF2 to be an input, as the pull-up or pull-
down will hold the pin in a known state and will not switch.
Active Configuration involves the use of a three-statable ex-
ternal driver connected to the Mode C pin. A driver’s output
enable should be connected to the DSP’s
RESET signal such
that it only drives the PF2 pin when
RESET is active (low).
When
RESET is deasserted, the driver should three-state, thus
allowing full use of the PF2 pin as either an input or output. To
minimize power consumption during power-down, configure
the programmable flag as an output when connected to a three-
stated buffer. This ensures that the pin will be held at a constant
level and will not oscillate should the three-state driver’s level
hover around the logic switching point.
IACK Configuration
Mode D = 0 and in host mode:
IACK is an active, driven signal
and cannot be wire OR-ed.
相關PDF資料
PDF描述
VI-B1N-CX-B1 CONVERTER MOD DC/DC 18.5V 75W
VE-21N-CY-F2 CONVERTER MOD DC/DC 18.5V 50W
ADSP-21369KSWZ-5A IC DSP 32BIT 366MHZ 208LQFP
TAP106M035BRW CAP TANT 10UF 35V 20% RADIAL
XC2C384-10FGG324C IC CR-II CPLD 384MCELL 324-FBGA
相關代理商/技術參數
參數描述
ADSP-2189MKSTZ-300 制造商:Analog Devices 功能描述:IC 16-BIT MICROCOMPUTER
ADSP-2189N 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP-2189NBCA-320 功能描述:IC DSP 16BIT 80MHZ 144CSPBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-2189NBCAZ-320 功能描述:IC DSP 16BIT 80MHZ 144CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-2189NBCAZ-3202 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*