參數資料
型號： ADSP-21992BSTZ
廠商： Analog Devices Inc
文件頁數： 46/60頁
文件大?。?/td> 0K
描述： IC DSP CONTROLLER 16BIT 176LQFP
標準包裝： 1
系列： ADSP-21xx
類型： 定點
接口： SPI，SSP
時鐘速率： 160MHz
非易失內存： 外部
芯片上RAM： 128kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 2.50V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 176-LQFP
供應商設備封裝： 176-LQFP（24x24）
包裝： 托盤
Rev. A
|
Page 50 of 60
|
August 2007
ADSP-21992
POWER DISSIPATION
Total power dissipation has two components, one due to inter-
nal circuitry and one due to the switching of external output
drivers. Internal power dissipation is dependent on the instruc-
tion execution sequence and the data operands involved.
The external component of total power dissipation is caused by
the switching of output pins. Its magnitude depends on:
Number of output pins that switch during each cycle (O)
The maximum frequency at which they can switch (f)
Their load capacitance (C)
Their voltage swing (VDD)
and is calculated by the formula below.
The load capacitance includes the package capacitance (CIN of
the processor). The switching frequency includes driving the
load high and then back low. Address and data pins can drive
high and low at a maximum rate of 1/(2tCK). The write strobe
can switch every cycle at a frequency of 1/tCK. Select pins switch
at 1/(2tCK), but selects can switch on each cycle. For example,
estimate PEXT with the following assumptions:
A system with one bank of external data memory—
asynchronous RAM (16-bit)
One 64K
16 RAM chip is used with a load of 10 pF
Maximum peripheral speed CCLK = 80 MHz, HCLK =
80 MHz
External data memory writes occur every other cycle, a rate
of 1/(4tHCLK), with 50% of the pins switching
The bus cycle time is 80 MHz (tHCLK = 12.5 ns)
The PEXT equation is calculated for each class of pins that can
drive as shown in Table 27.
A typical power consumption can now be calculated for these
conditions by adding a typical internal power dissipation with
the following formula.
where:
PEXT is from Table 27.
PINT is IDDINT
2.5 V, using the calculation IDDINT listed in
Note that the conditions causing a worst-case PEXT are different
from those causing a worst-case PINT. Maximum PINT cannot
occur while 100% of the output pins are switching from all ones
to all zeros. Note also that it is not common for an application to
have 100% or even 50% of the outputs switching
simultaneously.
PEXT
OC
×
VDD
2
×
f
×
=
PTOTAL P
=
EXT
PINT
+
Table 27. PEXT Calculation Example
Pin Type
No. of Pins
% Switching
C
f
VDD
2
= PEXT
Address
15
50
10 pF
20 MHz
10.9 V
= 0.01635 W
MSx
1
0
10 pF
20 MHz
10.9 V
= 0.0 W
WR
1
10 pF
40 MHz
10.9 V
= 0.00436 W
Data
16
50
10 pF
20 MHz
10.9 V
= 0.01744 W
CLKOUT
1
10 pF
80 MHz
10.9 V
= 0.00872 W
= 0.04687 W
相關PDF資料
PDF描述
HSM36DSEF CONN EDGECARD 72POS .156 EYELET
ADSP-21363BSWZ-1AA IC DSP 32BIT 333MHZ EPAD 144LQFP
MIC184YM IC SUPERVISOR LOCAL/REMOTE 8SOIC
VI-B1N-CW-B1 CONVERTER MOD DC/DC 18.5V 100W
PMEG2005AEV,115 SCHOTTKY RECT 20V 0.5A SOT666
相關代理商/技術參數
參數描述
ADSP-21992YBC 功能描述:IC DSP CTLR 16BIT 196CSPBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21992YST 制造商:Analog Devices 功能描述:
ADSP-21BT101JST 制造商:Analog Devices 功能描述:
ADSP21CSP01BS200 制造商:Rochester Electronics LLC 功能描述:- Bulk
ADSP21CSP01KS200 制造商:Rochester Electronics LLC 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*