參數資料
型號： ADSP-TS101SAB2Z000
廠商： Analog Devices Inc
文件頁數： 8/48頁
文件大?。?/td> 0K
描述： IC DSP FLOAT/FIXED 250MHZ 484BGA
標準包裝： 1
系列： TigerSHARC®
類型： 定點/浮點
接口： 主機接口，連接端口，多處理器
時鐘速率： 250MHz
非易失內存： 外部
芯片上RAM： 768kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.20V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 484-BFBGA
供應商設備封裝： 484-PBGA（19x19）
包裝： 托盤
Rev. C
|
Page 16 of 48
|
May 2009
ADSP-TS101S
Table 8. Pin Definitions—External Port SDRAM Controller
Signal
Type
Term
Description
MSSD
1
I/O/T (pu
2)
nc
Memory Select SDRAM. MSSD is asserted whenever the DSP accesses SDRAM memory space.
MSSD is a decoded memory address pin that is asserted whenever the DSP issues an SDRAM
command cycle (access to ADDR31:26 = 0b000001). MSSD in a multiprocessor system is driven
by the master DSP.
RAS
I/O/T (pu
2)
nc
Row Address Select. When sampled low, RAS indicates that a row address is valid in a read or
write of SDRAM. In other SDRAM accesses, RAS defines the type of operation to execute
according to SDRAM specification.
CAS1
I/O/T (pu2)
nc
Column Address Select. When sampled low, CAS indicates that a column address is valid in a
read or write of SDRAM. In other SDRAM accesses, CAS defines the type of operation to execute
according to the SDRAM specification.
LDQM
O/T (pu
2)
nc
Low Word SDRAM Data Mask. When LDQM is sampled high, the DSP three-states the SDRAM
DQ buffers. LDQM is valid on SDRAM transactions when CAS is asserted and is inactive on read
transactions. On write transactions, LDQM is active when accessing an odd address word on a
64-bit memory bus to disable the write of the low word.
HDQM
O/T (pu
2)
nc
High Word SDRAM Data Mask. When HDQM is sampled high, the DSP three-states the SDRAM
DQ buffers. HDQM is valid on SDRAM transactions when CAS is asserted and is inactive on read
transactions. On write transactions, HDQM is active when accessing an even address in word
accesses or is active when memory is configured for a 32-bit bus to disable the write of the high
word.
SDA10
O/T (pu
2)
nc
SDRAM Address bit 10 pin. Separate A10 signals enable SDRAM refresh operation while the DSP
executes non-SDRAM transactions.
SDCKE
I/O/T
(pu/pd2)
nc
SDRAM Clock Enable. Activates the SDRAM clock for SDRAM self-refresh or suspend modes. A
slave DSP in a multiprocessor system does not have the pull-up or pull-down. A master DSP (or
ID = 0 in a single processor system) has a 100 k
pull-up before granting the bus to the host,
except when the SDRAM is put in self-refresh mode. In self-refresh mode, the master has a
100 k
pull-down before granting the bus to the host.
SDWE1
I/O/T (pu2)
nc
SDRAM Write Enable. When sampled low while CAS is active, SDWE indicates an SDRAM write
access. When sampled high while CAS is active, SDWE indicates an SDRAM read access. In other
SDRAM accesses, SDWE defines the type of operation to execute according to SDRAM
specification.
Type column symbols: A = asynchronous; G = ground; I = input; O = output; o/d = open drain output; P = power supply;
pd = internal pull-down approximately 100 k; pu = internal pull-up approximately 100 k; T = three-state
Term (for termination) column symbols: epd = external pull-down approximately 10 k to VSS; epu = external pull-up approximately 10 k
to VDD-IO, nc = not connected; au = always used.
1 The internal pull-up may not be sufficient. A stronger pull-up may be necessary.
2 See Electrical Characteristics on Page 20 for maximum and minimum current consumption for pull-up and pull-down resistances.
3 The internal pull-down may not be sufficient. A stronger pull-down may be necessary.
Table 9. Pin Definitions—JTAG Port
Signal
Type
Term
Description
EMU
O (o/d)
nc
1
Emulation. Connected only to the DSP’s JTAG emulator target board connector.
TCK
I
epd or
Test Clock (JTAG). Provides an asynchronous clock for JTAG scan.
TDI
2
I (pu
3)nc1
Test Data Input (JTAG). A serial data input of the scan path.
Type column symbols: A = asynchronous; G = ground; I = input; O = output; o/d = open drain output; P = power supply;
pd = internal pull-down approximately 100 k; pu = internal pull-up approximately 100 k; T = three-state
Term (for termination) column symbols: epd = external pull-down approximately 10 k to VSS; epu = external pull-up approximately 10 k
to VDD-IO, nc = not connected; au = always used.
相關PDF資料
PDF描述
GBM08DRSN CONN EDGECARD 16POS DIP .156 SLD
AYM25DTBH CONN EDGECARD 50POS R/A .156 SLD
MAX6639FAEE+T IC 2CH TEMP MONITOR 16-QSOP
ADSP-TS101SAB1Z000 IC DSP CONTROLLER 6MBIT 625-BGA
GBM08DRSH CONN EDGECARD 16POS DIP .156 SLD
相關代理商/技術參數
參數描述
ADSP-TS101SAB2Z100 功能描述:IC DSP CTRLR 6MBIT 300MHZ 484BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-TS201SABP-050 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-TS201SABP-060 功能描述:IC PROCESSOR 600MHZ 576BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-TS201SABP-10X 制造商:Analog Devices 功能描述:
ADSP-TS201SABP-15X 制造商:Analog Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*