- 您現在的位置：買賣IC網 > PDF目錄19463 > ADSP-TS101SAB2Z100 (Analog Devices Inc)IC DSP CTRLR 6MBIT 300MHZ 484BGA PDF資料下載
參數資料
| 型號： | ADSP-TS101SAB2Z100 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 46/48頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP CTRLR 6MBIT 300MHZ 484BGA |
| 標準包裝： | 1 |
| 系列： | TigerSHARC® |
| 類型： | 定點/浮點 |
| 接口： | 主機接口，連接端口，多處理器 |
| 時鐘速率： | 300MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 768kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.20V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 484-BFBGA |
| 供應商設備封裝： | 484-PBGA（19x19） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁
ADSP-TS101S
Rev. C
|
Page 7 of 48
|
May 2009
Host Interface
The ADSP-TS101S provides an easy and configurable interface
between its external bus and host processors through the exter-
nal port. To accommodate a variety of host processors, the host
interface supports pipelined or slow protocols for accesses of the
host as slave. Each protocol has programmable transmission
parameters, such as idle cycles, pipe depth, and internal
wait cycles.
The host interface supports burst transactions initiated by a host
processor. After the host issues the starting address of the burst
and asserts the BRST signal, the DSP increments the address
internally while the host continues to assert BRST.
The host interface provides a deadlock recovery mechanism that
enables a host to recover from deadlock situations involving the
DSP. The BOFF signal provides the deadlock recovery mecha-
nism. When the host asserts BOFF, the DSP backs off the
current transaction and asserts HBG and relinquishes the exter-
nal bus.
The host can directly read or write the internal memory of the
ADSP-TS101S, and it can access most of the DSP registers,
including DMA control (TCB) registers. Vector interrupts sup-
port efficient execution of host commands.
Multiprocessor Interface
The ADSP-TS101S offers powerful features tailored to multi-
processing DSP systems through the external port and link
ports. This multiprocessing capability provides highest band-
width for interprocessor communication, including:
Up to eight DSPs on a common bus
On-chip arbitration for glueless multiprocessing
Link ports for point-to-point communication
The external port and link ports provide integrated, glueless
multiprocessing support.
The external port supports a unified address space (see Figure 3)
that enables direct interprocessor accesses of each
ADSP-TS101S processor’s internal memory and registers. The
DSP’s on-chip distributed bus arbitration logic provides simple,
glueless connection for systems containing up to eight ADSP-
TS101S processors and a host processor. Bus arbitration has a
rotating priority. Bus lock supports indivisible read-modify-
write sequences for semaphores. A bus fairness feature prevents
one DSP from holding the external bus too long.
The DSP’s four link ports provide a second path for interproces-
sor communications with throughput of 1G bytes per second.
The cluster bus provides 800M bytes per second throughput—
with a total of 1.8G bytes per second interprocessor bandwidth.
SDRAM Controller
The SDRAM controller controls the ADSP-TS101S processor’s
transfers of data to and from synchronous DRAM (SDRAM).
The throughput is 32 or 64 bits per SCLK cycle using the exter-
nal port and SDRAM control pins.
The SDRAM interface provides a glueless interface with stan-
dard SDRAMs—16M bit, 64M bit, 128M bit, and 256M bit. The
DSP directly supports a maximum of 64M words 32 bits of
SDRAM. The SDRAM interface is mapped in external memory
in the DSP’s unified memory map.
EPROM Interface
The ADSP-TS101S can be configured to boot from external
8-bit EPROM at reset through the external port. An automatic
process (which follows reset) loads a program from the EPROM
into internal memory. This process uses 16 wait cycles for each
read access. During booting, the BMS pin functions as the
EPROM chip select signal. The EPROM boot procedure uses
DMA Channel 0, which packs the bytes into 32-bit instructions.
Applications can also access the EPROM (write flash memories)
during normal operation through DMA.
The EPROM or flash memory interface is not mapped in the
DSP’s unified memory map. It is a byte address space limited to
a maximum of 16M bytes (24 address bits). The EPROM or
flash memory interface can be used after boot via a DMA.
DMA CONTROLLER
The ADSP-TS101S processor’s on-chip DMA controller, with
14 DMA channels, provides zero-overhead data transfers with-
out processor intervention. The DMA controller operates
independently and invisibly to the DSP’s core, enabling DMA
operations to occur while the DSP’s core continues to execute
program instructions. The DMA controller performs DMA
transfers between:
Internal memory and external memory and memory-
mapped peripherals
Internal memory of other DSPs on a common bus, a host
processor, or link port I/O
External memory and external peripherals or link port I/O
External bus master and internal memory or link port I/O
The DMA controller provides a number of additional features.
The DMA controller supports flyby transfers. Flyby operations
only occur through the external port (DMA Channel 0) and do
not involve the DSP’s core. The DMA controller acts as a con-
duit to transfer data from one external device to another
through external memory. During a transaction, the DSP:
Relinquishes the external data bus
Outputs addresses, memory selects (MS1–0, MSSD, RAS,
CAS, and SDWE) and the FLYBY, IOEN, and RD/WR
strobes
Responds to ACK
DMA chaining is also supported by the DMA controller. DMA
chaining operations enable applications to automatically link
one DMA transfer sequence to another for continuous trans-
mission. The sequences can occur over different DMA channels
and have different transmission attributes.
相關PDF資料 |
PDF描述 |
|---|---|
| TPSC156K020H0400 | CAP TANT 15UF 20V 10% 2312 |
| 172-E09-202R001 | CONN DB9 FEMALE SOLDER CUP TIN |
| VE-2WT-CY-F3 | CONVERTER MOD DC/DC 6.5V 50W |
| 172-E15-103R911 | CONN DB15 MALE SOLDER CUP NICKEL |
| AD7818ARM-REEL | IC ADC 10BIT W/TEMP SNSR 8-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-TS201SABP-050 | 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-TS201SABP-060 | 功能描述:IC PROCESSOR 600MHZ 576BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-TS201SABP-10X | 制造商:Analog Devices 功能描述: |
| ADSP-TS201SABP-15X | 制造商:Analog Devices 功能描述: |
| ADSP-TS201SABP-ENG | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。