- 您現在的位置：買賣IC網 > PDF目錄10600 > ADV7180KST48Z (Analog Devices Inc)IC VID DECOD SDTV 10BIT 48LQFP PDF資料下載
參數資料
| 型號： | ADV7180KST48Z |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 33/116頁 |
| 文件大小： | 0K |
| 描述： | IC VID DECOD SDTV 10BIT 48LQFP |
| 標準包裝： | 1 |
| 類型： | 視頻解碼器 |
| 應用： | 數碼相機，手機，便攜式視頻 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Data Sheet
ADV7180
Rev. I | Page 23 of 116
GLOBAL CONTROL REGISTERS
Register control bits listed in this section affect the whole chip.
POWER-SAVING MODES
Power-Down
PDBP, Address 0x0F[2]
The digital supply of the ADV7180 can be shut down by using
the PWRDWN pin or via I2C1 (see the PWRDWN, Address
pin has the higher priority. The default is to give the pin
(PWRDWN) priority2. This allows the user to have the
ADV7180 powered down by default at power-up without the
need for an I2C write.
When PDBP is 0 (default), the digital supply power is controlled
by the PWRDWN pin2 (the PWRDWN bit, Address 0x0F[5], is
disregarded).
When PDBP is 1, the PWRDWN bit has priority (the pin is
disregarded).
PWRDWN, Address 0x0F[5]
When PDBP is set to 1, setting the PWRDWN bit switches the
ADV7180 to a chip-wide power-down mode. The power-down
stops the clock from entering the digital section of the chip,
thereby freezing its operation. No I2C bits are lost during power-
down. The PWRDWN bit also affects the analog blocks and
switches them into low current modes. The I2C interface is
unaffected and remains operational in power-down mode.
The ADV7180 leaves the power-down state if the PWRDWN bit is
PDBP must be set to 1 for the PWRDWN bit to power down
the ADV7180.
When PWRDWN is 0 (default), the chip is operational. When
PWRDWN is 1, the ADV7180 is in a chip-wide power-down mode.
RESET CONTROL
Reset, Chip Reset, Address 0x0F[7]
Setting this bit, which is equivalent to controlling the RESET pin
to their default/power-up values. Note that some register bits do
not have a reset value specified. They keep their last written value.
Those bits are marked as having a reset value of x in the register
tables (see Table 107 and Table 108). After the reset sequence,
the part immediately starts to acquire the incoming video signal.
1
For 32-lead, I2C is the only power-down option.
2
For 64-lead, 48-lead, and 40-lead only.
After setting the reset bit (or initiating a reset via the RESET pin),
the part returns to the default for its primary mode of operation.
All I2C bits are loaded with their default values, making this bit
self-clearing.
Executing a software reset takes approximately 2 ms. However,
it is recommended to wait 5 ms before any further I2C writes are
performed.
The I2C master controller receives a no acknowledge condition
on the ninth clock cycle when chip reset is implemented (see
the MPU Port Description section).
When the reset bit is 0 (default), operation is normal.
When the reset bit is 1, the reset sequence starts.
GLOBAL PIN CONTROL
Three-State Output Drivers
TOD, Address 0x03[6]
This bit allows the user to three-state the output drivers of the
Upon setting the TOD bit, the P15 to P0 (P7 to P0 for the 48-lead,
40-lead, and 32-lead devices), HS, VS, FIELD (VS/FIELD pin for
the 48-lead, 40-lead, and 32-lead LFCSP), and SFL pins are
three-stated.
The timing pins (HS, VS, FIELD) can be forced active via the
TIM_OE bit. For more information on three-state control, see
Enable sections.
Individual drive strength controls are provided via the
DR_STR_x bits.
When TOD is 0 (default), the output drivers are enabled.
When TOD is 1, the output drivers are three-stated.
Three-State LLC Driver
TRI_LLC, Address 0x1D[7]
This bit allows the output drivers for the LLC pin of the
ADV7180 to be three-stated. For more information on three-
state control, refer to the Three-State Output Drivers and the
Timing Signals Output Enable sections.
Individual drive strength controls are provided via the
DR_STR_x bits.
When TRI_LLC is 0 (default), the LLC pin drivers work
according to the DR_STR_C[1:0] setting (pin enabled).
When TRI_LLC is 1, the LLC pin drivers are three-stated.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2WD-IW-F4 | CONVERTER MOD DC/DC 85V 100W |
| VE-B7R-MX-F2 | CONVERTER MOD DC/DC 7.5V 75W |
| PX0738/P | CONN JAM NUT 6POS W/PINS |
| ADV7611BSWZ-P-RL | IC RCVR HDMI 165MHZ LP 64LQFP |
| VE-B7R-MX-F1 | CONVERTER MOD DC/DC 7.5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7180KST48Z-RL | 功能描述:視頻 IC 48-Lead Low Profile Quad Flat Package RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| ADV7180WBCP32Z | 制造商:Analog Devices 功能描述:IC, 10-BIT 4X OVERSAMPLING SDTV DECODER 制造商:Analog Devices 功能描述:SDTV VIDEO DECODER 32-PIN LFCSP EP TRAY - Trays |
| ADV7180WBCP32Z-RL | 制造商:Analog Devices 功能描述:10-BIT, 4? OVERSAMPLING SDTV VIDEO DECODER - Tape and Reel |
| ADV7180WBCPZ | 功能描述:IC VIDEO DECODER SDTV 40LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
| ADV7180WBCPZ-REEL | 功能描述:IC VIDEO DECODER SDTV 40LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
發布緊急采購，3分鐘左右您將得到回復。