- 您現在的位置：買賣IC網 > PDF目錄10972 > ADV7189BKSTZ (Analog Devices Inc)IC DECODER VIDEO W/ADC 80LQFP PDF資料下載
參數資料
| 型號： | ADV7189BKSTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 23/104頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DECODER VIDEO W/ADC 80LQFP |
| 標準包裝： | 1 |
| 類型： | 視頻解碼器 |
| 應用： | 機頂盒，視頻播放器，錄音機 |
| 電壓 - 電源，模擬： | 3.15 V ~ 3.45 V |
| 電壓 - 電源，數字： | 1.65 V ~ 2 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-LQFP（14x14） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 788 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
ADV7189B
Rev. B | Page 25 of 104
DEF_VAL_EN Default Value Enable, Address 0x0C[0]
This bit forces the use of the default values for Y, Cr, and Cb.
Refer to the descriptions for DEF_Y and DEF_C for additional
information. In this mode, the decoder also outputs a stable
27 MHz clock, HS, and VS.
Setting DEF_VAL_EN to 0 (default) outputs a colored screen
determined by user-programmable Y, Cr, and Cb values when
the decoder free-runs. Free-run mode is turned on and off by the
DEF_VAL_AUTO_EN bit.
Setting DEF_VAL_EN to 1 forces a colored screen output
determined by user-programmable Y, Cr, and Cb values.
This overrides picture data even if the decoder is locked.
DEF_VAL_AUTO_EN Default Value Automatic Enable,
Address 0x0C[1]
This bit enables the automatic use of the default values for Y, Cr,
and Cb when the ADV7189B cannot lock to the video signal.
Setting DEF_VAL_AUTO_EN to 0 disables free-run mode.
If the decoder is unlocked, it outputs noise.
Setting DEF_VAL_EN to 1 (default) enables free-run mode.
A colored screen set by the user-programmable Y, Cr, and Cb
values is displayed when the decoder loses lock.
CLAMP OPERATION
The input video is ac-coupled into the ADV7189B through a
0.1 μF capacitor. The recommended range of the input video
signal range be 0.5 V to 1.6 V (typically 1 V p-p). If the signal
exceeds the range, it cannot be processed correctly in the decoder.
Because the input is ac-coupled into the decoder, its dc value
needs to be restored. This process is referred to as clamping the
video. This section explains the general process of clamping on
the ADV7189B and shows the different ways in which a user can
configure its behavior.
The ADV7189B uses a combination of current sources and a
digital processing block for clamping, as shown in
171H
Figure 10.
The analog processing channel shown is replicated three times
inside the IC. While only one single channel (and only one
ADC) is needed for a CVBS signal, two independent channels
are needed for YC (S-VHS) type signals, and three independent
channels are needed to allow component signals (YPrPb) to
be processed.
The clamping can be divided into two sections:
Clamping before the ADC (analog domain): current sources.
Clamping after the ADC (digital domain): digital
processing block.
The ADCs can digitize an input signal only if it resides within
the ADC’s 1.6 V input voltage range. An input signal with a dc
level that is too large or too small is clipped at the top or bottom
of the ADC range.
The primary task of the analog clamping circuits is to ensure
the video signal stays within the valid ADC input window, so
the analog-to-digital conversion can take place. It is not neces-
sary to clamp the input signal with a very high accuracy in the
analog domain as long as the video signal fits the ADC range.
After digitization, the digital fine clamp block corrects for any
remaining variations in dc level. Since the dc level of an input
video signal refers directly to the brightness of the picture
transmitted, it is important to perform a fine clamp with high
accuracy; otherwise, brightness variations can occur. Dynamic
changes in the dc level lead to visually objectionable artifacts so
it is recommended not to use dynamic changes.
The clamping scheme has to complete two tasks. It must be
able to acquire a newly connected video signal with a com-
pletely unknown dc level, and it must maintain the dc level
during normal operation.
For quickly acquiring an unknown video signal, the large current
clamps can be activated. It is assumed the amplitude of the
video signal is of a nominal value at this point. Control of the
coarse and fine current clamp parameters is performed auto-
matically by the decoder.
Standard definition video signals may have excessive noise
on them. In particular, CVBS signals transmitted by terrestrial
broadcast and demodulated using a tuner usually show very
large levels of noise (>100 mV). A voltage clamp is unsuitable
for this type of video signal. Instead, the ADV7189B employs a
set of four current sources that cause coarse (>0.5 mA) and fine
(<0.1 mA) currents to flow into and away from the high imped-
ance node that carries the video signal (see
172H
Figure 10).
04983-
0-
010
COARSE
CURRENT
SOURCES
FINE
CURRENT
SOURCES
DATA
PRE-
PROCESSOR
(DPP)
ADC
SDP
WITH DIGITAL
FINE CLAMP
CLAMP CONTROL
ANALOG
VIDEO
INPUT
Figure 10. Clamping Overview
相關PDF資料 |
PDF描述 |
|---|---|
| VI-214-IY-F4 | CONVERTER MOD DC/DC 48V 50W |
| ADV7183BKSTZ | IC VIDEO DECODER NTSC 80-LQFP |
| VI-213-IY-F3 | CONVERTER MOD DC/DC 24V 50W |
| VE-23J-IY-F2 | CONVERTER MOD DC/DC 36V 50W |
| LF10WBR-12P | CONN RCPT WATERPROOF 12POS MALE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7189BKSTZ10F | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
| ADV7189BKSTZ10F2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
| ADV7189BST | 制造商:Analog Devices 功能描述: |
| ADV7189KST | 制造商:Rochester Electronics LLC 功能描述:12BIT NTSC/PAL/SECAMVIDDECOD I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC VIDEO ENCODER |
| ADV7189XST | 制造商:Analog Devices 功能描述:54MHZ NTSC/PAL ENCODER(DNR+MACROVISON)IC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。