- 您現在的位置：買賣IC網 > PDF目錄10972 > ADV7189BKSTZ (Analog Devices Inc)IC DECODER VIDEO W/ADC 80LQFP PDF資料下載
參數資料
| 型號： | ADV7189BKSTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 41/104頁 |
| 文件大小： | 0K |
| 描述： | IC DECODER VIDEO W/ADC 80LQFP |
| 標準包裝： | 1 |
| 類型： | 視頻解碼器 |
| 應用： | 機頂盒，視頻播放器，錄音機 |
| 電壓 - 電源，模擬： | 3.15 V ~ 3.45 V |
| 電壓 - 電源，數字： | 1.65 V ~ 2 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-LQFP（14x14） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 788 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
ADV7189B
Rev. B | Page 41 of 104
VS and FIELD Configuration
The following controls allow the user to configure the behav-
ior of the VS and FIELD output pins, as well as to generate
embedded AV codes:
ADV encoder-compatible signals via NEWAVMODE
PVS, PF
HVSTIM
VSBHO, VSBHE
VSEHO, VSEHE
For NTSC control:
NVBEGDELO, NVBEGDELE, NVBEGSIGN,
NVBEG[4:0]
NVENDDELO, NVENDDELE, NVENDSIGN,
NVEND[4:0]
NFTOGDELO, NFTOGDELE, NFTOGSIGN,
NFTOG[4:0]
For PAL control:
PVBEGDELO, PVBEGDELE, PVBEGSIGN,
PVBEG[4:0]
PVENDDELO, PVENDDELE, PVENDSIGN,
PVEND[4:0]
PFTOGDELO, PFTOGDELE, PFTOGSIGN,
PFTOG[4:0]
NEWAVMODE New AV Mode, Address 0x31[4]
When NEWAVMODE is 0, EAV/SAV codes are generated to
suit ADI encoders. No adjustments are possible.
Setting NEWAVMODE to 1 (default) enables the manual
position of the VSYNC, Field, and AV codes using
Registers 0x34 to 0x37 and Register 0xE5 to 0xEA. Default
register settings are CCIR656 compliant; see
207H
Figure 21 for NTSC
and
208H
Figure 26 for PAL. For recommended manual user settings,
see
209H
Table 56 and
210H
Figure 22 for NTSC; see
211H
Table 57 and
212H
Figure 27
for PAL.
HVSTIM Horizontal VS Timing, Address 0x31[3]
The HVSTIM bit allows the user to select where the VS signal
is being asserted within a line of video. Some interface circuitry
can require VS to go low while HS is low.
When HVSTIM is 0 (default) the start of the line is relative
to HSE.
When HVSTIM is 1, the start of the line is relative to HSB.
VSBHO VS Begin Horizontal Position Odd, Address 0x32[7]
The VSBHO and VSBHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSBHO is 0 (default), the VS pin goes high at the middle
of a line of video (odd field).
When VSBHO is 1, the VS pin changes state at the start of a line
(odd field).
VSBHE VS Begin Horizontal Position Even, Address 0x32[6]
The VSBHO and VSBHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSBHE is 0 (default), the VS pin goes high at the middle
of a line of video (even field).
When VSBHE is 1, the VS pin changes state at the start of a line
(even field).
VSEHO VS End Horizontal Position Odd, Address 0x33{7]
The VSEHO and VSEHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSEHO is 0, the VS pin goes low (inactive) at the middle
of a line of video (odd field).
When VSEHO is 1 (default), the VS pin changes state at the
start of a line (odd field).
VSEHE VS End Horizontal Position Even, Address 0x33[6]
The VSEHO and VSEHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSEHE is 0 (default), the VS pin goes low (inactive) at
the middle of a line of video (even field).
When VSEHE is 1, the VS pin changes state at the start of a line
(even field).
PVS Polarity VS, Address 0x37[5]
The polarity of the VS pin can be inverted using the PVS bit.
When PVS is 0 (default), VS is active high. When PVS is 1, VS is
active low.
PF Polarity FIELD, Address 0x37[3]
The polarity of the FIELD pin can be inverted using the PF bit.
When PF is 0 (default), FIELD is active high. When PF is 1,
FIELD is active low.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-214-IY-F4 | CONVERTER MOD DC/DC 48V 50W |
| ADV7183BKSTZ | IC VIDEO DECODER NTSC 80-LQFP |
| VI-213-IY-F3 | CONVERTER MOD DC/DC 24V 50W |
| VE-23J-IY-F2 | CONVERTER MOD DC/DC 36V 50W |
| LF10WBR-12P | CONN RCPT WATERPROOF 12POS MALE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7189BKSTZ10F | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
| ADV7189BKSTZ10F2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
| ADV7189BST | 制造商:Analog Devices 功能描述: |
| ADV7189KST | 制造商:Rochester Electronics LLC 功能描述:12BIT NTSC/PAL/SECAMVIDDECOD I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC VIDEO ENCODER |
| ADV7189XST | 制造商:Analog Devices 功能描述:54MHZ NTSC/PAL ENCODER(DNR+MACROVISON)IC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。