- 您現在的位置：買賣IC網 > PDF目錄366488 > AM29LV160MB100FI (Advanced Micro Devices, Inc.) 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit 3.0 Volt-only Boot Sector Flash Memory PDF資料下載
參數資料
| 型號： | AM29LV160MB100FI |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit 3.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 16兆位（2米× 8位/ 1個M x 16位），3.0伏的MirrorBit只引導扇區閃存 |
| 文件頁數： | 20/60頁 |
| 文件大小： | 1849K |
| 代理商： | AM29LV160MB100FI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
18
Am29LV160M
25974B0 August 11, 2003
P r e l i m i n a r y
SecSi (Secured Silicon) Sector Flash Memory Region
The SecSi (Secured Silicon) Sector feature provides a Flash memory region that
enables permanent part identification through an Electronic Serial Number
(ESN). The SecSi Sector is 256 bytes in length, and uses a SecSi Sector Indica-
tor Bit (DQ7) to indicate whether or not the SecSi Sector is locked when shipped
from the factory. This bit is permanently set at the factory and cannot be
changed, which prevents cloning of a factory locked part. This ensures the secu-
rity of the ESN once the product is shipped to the field.
The device is offered with the SecSi Sector either customer lockable (standard
shipping option) or factory locked (contact a sales office or representative for or-
dering information). The customer-lockable version is shipped with the SecSi
Sector unprotected, allowing customers to program the sector after receiving
the device. The customer-lockable version also has the SecSi Sector Indicator
Bit permanently set to a “0.” The factory-locked version is always protected
when shipped from the factory, and has the SecSi (Secured Silicon) Sector Indi-
cator Bit permanently set to a “1.” Thus, the SecSi Sector Indicator Bit prevents
customer-lockable devices from being used to replace devices that are factory
locked.
Note that the ACC function and unlock bypass modes are not available
when the SecSi Sector is enabled.
The SecSi sector address space in this device is allocated as follows:
Table 5. SecSi Sector Addressing
The system accesses the SecSi Sector through a command sequence (see “En-
ter SecSi Sector/Exit SecSi Sector Command Sequence”). After the system has
written the Enter SecSi Sector command sequence, it may read the SecSi Sector
by using the addresses normally occupied by the first sector (SA0). This mode of
operation continues until the system issues the Exit SecSi Sector command se-
quence, or until power is removed from the device. On power-up, or following a
hardware reset, the device reverts to sending commands to sector SA0.
Customer Lockable: SecSi Sector NOT Programmed or Protected
At the Factory
Unless otherwise specified, the device is shipped such that the customer may
program and protect the 256-byte SecSi sector.
The system may program the SecSi Sector using the write-buffer, accelerated
and/or unlock bypass methods, in addition to the standard programming com-
mand sequence. See Command Definitions.
Programming and protecting the SecSi Sector must be used with caution since,
once protected, there is no procedure available for unprotecting the SecSi Sec-
tor area and none of the bits in the SecSi Sector memory space can be modified
in any way.
The SecSi Sector area can be protected using one of the following procedures:
Write the three-cycle Enter SecSi Sector Region command sequence, and
then follow the in-system sector protect algorithm as shown in Figure 2, ex-
SecSi Sector Address Range
Customer
Lockable
ESN Factory
Locked
ExpressFlash
Factory Locked
x16
x8
000000h–
000007h
000000h–
00000Fh
Determined by
customer
ESN
ESN or determined
by customer
000008h–
00007Fh
000010h–
0000FFh
Unavailable
Determined
by customer
相關PDF資料 |
PDF描述 |
|---|---|
| Am29LV160MT100 | CAP 0.01UF 100V 100V X7R RAD.20 .20X.20 BULK M-MIL-PRF-39014 STANDOFF |
| AM29LV160MT100EI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV160MT100FI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV160MT100WAI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV160MB100WAI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit 3.0 Volt-only Boot Sector Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV160MB100PCIT | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 16MBIT 2MX8/1MX16 100NS 64BGA - Tape and Reel |
| AM29LV160MB-100WAI | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 16M-Bit 2M x 8/1M x 16 100ns 48-Pin FBGA |
| AM29LV160MB120EI | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 16M-Bit 2M x 8/1M x 16 120ns 48-Pin TSOP |
| AM29LV160MB70EI | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 16MBIT 2MX8/1MX16 70NS 48TSOP - Trays |
| AM29LV160MB90EI | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 16M-Bit 2M x 8/1M x 16 90ns 48-Pin TSOP |
發布緊急采購，3分鐘左右您將得到回復。