- 您現在的位置：買賣IC網 > PDF目錄362306 > AMD-K6-2 AMD-K6-2 - AMD-K6-2 Processor Data Sheet PDF資料下載
參數資料
| 型號： | AMD-K6-2 |
| 英文描述： | AMD-K6-2 - AMD-K6-2 Processor Data Sheet |
| 中文描述： | 的AMD - K6 - 2 -的AMD - K6 - 2處理器數據手冊 |
| 文件頁數： | 24/44頁 |
| 文件大小： | 2886K |
| 代理商： | AMD-K6-2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
16
AMD-K5 Processor Thermal Considerations
AMD-K5 Processor Thermal Considerations
20092B/0—Sep1996
When using thermal conductive adhesive tape it is important
to select one tape that fills the gap between the two surfaces
(tolerance of both processor case top and heat sink is worst
case of 0.003 inch). Therefore, tape thickness of a minimum of
0.006 inch should be used to fill the microscopic holes in the
surfaces.
When ceramic packages are used, some manufacturers recom-
mend using a primer (e.g., 1088 Primer by Chomerics) on the
ceramic package before the adhesive tape is applied. The
primer fills the porous ceramic surface to allow the adhesive
tape to obtain a greater bond surface.
The procedure for applying thermal tape to the AMD-K5 pro-
cessor and the heat sink is:
1. Cut the tape to a size that can cover the entire area between
the AMD-K5 processor and the heat sink.
2. Make sure that all oils and dust are removed from the
AMD-K5 processor case top and the bottom of the heat sink
to ensure maximum adhesion. This is done by using a lint-
free cloth with an industrial cleaner (e.g., toluene, acetone,
or isopropyl alcohol) and rubbing both surfaces.
3. Peel away the clear release liner from the non-embossed
side of the thermal adhesive tape.
4. Apply tape to the AMD-K5 processor case top.
5. Smooth over the entire surface of the tape with moderate
pressure, using the applicator provided.
6. Remove the blue liner from the embossed side of the tape.
7. Align both the AMD-K5 processor and the heat sink and
apply pressure (e.g., 10 psi).
Note:
Improved surface contact can be achieved by heating the
tape with a conventional heat gun, not to exceed 100
o
C,
prior to applying pressure.
8. Approximately 70% of the ultimate adhesion is achieved at
initial contact. At least 36 hours is required before ultimate
adhesive strength is achieved.
相關PDF資料 |
PDF描述 |
|---|---|
| AMD-K6-2E | AMD-K6-2E - AMD-K6-2E Embedded Processor Data Sheet |
| AMD-K6-III | AMD-K6-III - AMD-K6-III Processor Data Sheet |
| AMD-K6-III-P | Mobile AMD-K6?-III-P Processor Data Sheet |
| AMD-K7500MTR51BC | MICROPROCESSOR|32-BIT|CMOS|CARD|PLASTIC |
| AMD-K7550MTR51BA | MICROPROCESSOR|32-BIT|CMOS|CARD|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMD-K6-2/300AFR | 制造商:Advanced Micro Devices 功能描述:Microprocessor, 32 Bit, 321 Pin, Ceramic, PGA |
| AMDK62/350AFK | 制造商:Advanced Micro Devices 功能描述: |
| AMD-K6-2/400ACR | 制造商:Advanced Micro Devices 功能描述:32-BIT, 400 MHZ, RISC PROCESSOR, CPGA321 |
| AMD-K6-2/500AFX | 制造商:Advanced Micro Devices 功能描述:32-BIT, 500 MHz, RISC PROCESSOR, CPGA321 |
| AMD-K6-2+/450ACR | 制造商:Advanced Micro Devices 功能描述:32-BIT, 450 MHZ, RISC PROCESSOR, CPGA321 |
發布緊急采購，3分鐘左右您將得到回復。