參數資料
型號: AN10E40
廠商: Electronic Theatre Controls, Inc.
英文描述: Field Programmable Analog Array
中文描述: 現場可編程模擬陣列
文件頁數: 8/36頁
文件大?。?/td> 293K
代理商: AN10E40
4
CAB Details
The SRAM block which controls routing connections and CAB behavior is loaded during configuration time.
Configuration typically occurs at power up as an automatic process but can of course be re-initiated at any time.
The ability to re-configure the part at any time gives the user incredible flexibility in system design.
Programmable capacitor banks and local switching in both the input paths to the op-amp and a programmable
capacitor bank in the op-amp’s feedback path provide all the resources required to realize a very large number of
analog processing circuits.
Figure 3. Block Level View of the basic CAB
Connection between other CAB’s on the device and to the outside world are accomplished using the Local Inputs,
Local Output, and Global routing resources.
Routing Resources
The most expedient way to gain understanding of the routing resources available on the AN10E40 is to use the
associated AnadigmDesigner design software. The routing resources and your connections to them are
represented in an intuitively obvious fashion.
Local routing resources are only shown (as fly lines or rubber band lines) in the design software screen once they
are used. A CAB output may be connected to an input in any of its 8 adjacent neighbors, and additionally to the
CAB in the same row and to the right two locations.
Global routing resources allow you to move signals to disparate locations on the die. There are a total of 10
horizontal global routes and 12 vertical global routes within the array. A CAB’s output can be connected to either of
the two adjacent right or two adjacent down global routes. A CAB’s input can be driven by one of the two adjacent
right or adjacent down global routes (which one of these two routes alternates with location in the array).
Connections to the chip’s programmable reference voltage generator are only available using Global routing
resources.
Clock Generation
Recall from the discussion on switched capacitor basics that the behavior of our simple circuit was influenced by
both the value of the capacitor as well as the frequency of the clock. So it is with IPmodules placed into the CABs of
the AN10E40 array. IPmodule input clocks are all derived from the master CLOCK input pin. The maximum rated
frequency of this input is currently specified to be 20 MHz. The master clock is split into 4 pairs of non-overlapping
clocks and bussed to each of the CABs. CLOCK[3:0] are derived from the dividing the master CLOCK input down
by a factor of 1 or from 2 to 62 (in increments of two). The maximum allowable clock frequency into an IPmodule is
OpAmp
L
Configuration Memory (SRAM)
Local Outputs
Global Outputs
L
Global In
相關PDF資料
PDF描述
AN17850A Silicon Monolithic Bipolar IC
AN19 AN19 - How 2 Use de KITS SPC DC Motor with StarTech PPI Card
AN2110S JT 66C 66#22D SKT RECP
AN220D04-DEVLP DANAMICALLY RECONFIGURABLE FPAA
AN220D04-EVAL DANAMICALLY RECONFIGURABLE FPAA
相關代理商/技術參數
參數描述
AN10-N01 制造商:SMC Corporation of America 功能描述:Silencer, Compact Resin, Male Thread, 1/8" NPT Port, 30 dB(A), Model AN10
AN110 制造商:SILABS 制造商全稱:SILABS 功能描述:16-BIT PWM USING AN ON-CHIP TIMER
AN110-01 制造商:SMC Corporation of America 功能描述:MUFFLER 1/8 PT 制造商:SMC 功能描述:TCT Bulk
AN11006 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single stage 2.3_2.7GHz LNA with BFU730F
AN11007 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single stage 5-6 GHz WLAN LNA with BFU730F