參數資料
型號： CDB4351
廠商： Cirrus Logic Inc
文件頁數： 13/37頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR CS4351 DAC
標準包裝： 1
系列： Popguard®
DAC 的數量： 2
位數： 24
采樣率（每秒）： 192k
數據接口： 串行
DAC 型： 電壓
工作溫度： -10°C ~ 70°C
已供物品： 板，纜線，CD
已用 IC / 零件： CS4351
產品目錄頁面： 757 (CN2011-ZH PDF)
相關產品： CS4351-DZZ-ND - IC DAC STER 112DB 192KHZ 20TSSOP
598-1055-5-ND - IC DAC STER 112DB 192KHZ 20TSSOP
其它名稱： 598-1152
20
DS566F1
CS4351
4.9
Control Port Interface
The control port is used to load all the internal register settings (see Section 6). The operation of the control
port may be completely asynchronous with the audio sample rate. However, to avoid potential interference
problems, the control port pins should remain static if no operation is required.
The control port operates in one of two modes: IC or SPI.
4.9.1
MAP Auto Increment
The device has MAP (memory address pointer) auto increment capability enabled by the INCR bit (also
the MSB) of the MAP. If INCR is set to 0, MAP will stay constant for successive IC writes or reads and
SPI writes. If INCR is set to 1, MAP will auto increment after each byte is written, allowing block reads or
writes of successive registers.
4.9.2
IC Mode
In the IC mode, data is clocked into and out of the bi-directional serial control data line, SDA, by the serial
control port clock, SCL (see Figure 9 for the clock to data relationship). There is no CS pin. Pin AD0 en-
ables the user to alter the chip address (100110[AD0][R/W]) and should be tied to VL or GND as required,
before powering up the device. If the device ever detects a high to low transition on the AD0/CS pin after
power-up, SPI mode will be selected.
4.9.2.1
IC Write
To write to the device, follow the procedure below while adhering to the control port Switching Specifica-
tions in Section 8.
1. Initiate a START condition to the IC bus followed by the address byte. The upper 6 bits must be
100110. The seventh bit must match the setting of the AD0 pin, and the eighth must be 0. The eighth
bit of the address byte is the R/W bit.
2. Wait for an acknowledge (ACK) from the part, then write to the memory address pointer, MAP. This
byte points to the register to be written.
3. Wait for an acknowledge (ACK) from the part, then write the desired data to the register pointed to
by the MAP.
4. If the INCR bit (see Section 4.9.1) is set to 1, repeat the previous step until all the desired registers
are written, then initiate a STOP condition to the bus.
5. If the INCR bit is set to 0 and further IC writes to other registers are desired, it is necessary to initiate
a repeated START condition and follow the procedure detailed from step 1. If no further writes to oth-
er registers are desired, initiate a STOP condition to the bus.
相關PDF資料
PDF描述
VI-B11-EY CONVERTER MOD DC/DC 12V 50W
GMA10DRMD-S288 CONN EDGECARD 20POS .125 EXTEND
GBM28DCWI CONN EDGECARD 56POS DIP .156 SLD
STD03W-R WIRE & CABLE MARKERS
AD9739A-FMC-EBZ BOARD EVAL W/FMC CONN FPGA DEV
相關代理商/技術參數
參數描述
CDB4352 功能描述:音頻 IC 開發工具 Eval Bd 192kHz DAC w/LD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4353 功能描述:音頻 IC 開發工具 3.3V Str DAC w/2Vrms line out Eval Bd RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4354 功能描述:音頻 IC 開發工具 Eval Board 5V DAC w/ 2Vrms line driver RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4360 功能描述:音頻 IC 開發工具 Eval Bd 102dB 192kHz 6-Ch DAC RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4361 功能描述:音頻 IC 開發工具 Eval Bd 105dB 192kHz 6-Ch DAC RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*