參數資料
型號： CR16MCS9VJE8
英文描述： Microcontroller
中文描述： 微控制器
文件頁數： 120/157頁
文件大?。?/td> 1256K
代理商： CR16MCS9VJE8
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁當前第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
www.national.com
120
with ADDATA3. After it loads all four registers, it clears the
START bit and sets the EOC (end of conversion) bit. If the A/
D Converter interrupt is enabled, an interrupt to the CPU is
generated at this time.
22.1.4
In the 4-channel scan, continuous conversion mode, the A/D
Converter performs conversions repeatedly using four adja-
cent input channels.
The software starts conversion operations by setting the
START bit. The A/D Converter performs four A/D conver-
sions in sequence using four adjacent channels, starting with
the specified channel and pausing only for the programmable
sampling delay time. It loads the four results into the A/D data
registers in sequence, starting with ADDATA0 and ending
with ADDATA3. After it loads all four registers, it sets the EOC
(end of conversion) bit. If the A/D Converter interrupt is en-
abled, an interrupt to the CPU is generated at this time.
The START bit remains set until cleared by the software. If
the software does not clear the START bit, the A/D Converter
continues performing conversions, repeating the same se-
quence using the same four input channels and the same se-
quence of data registers. To prevent an overrun error, the
software must read the results from the data registers before
the A/D Converter writes the next result into ADDATA0.
When the software clears the START bit, the A/D Converter
first completes the 4-channel conversion sequence currently
in progress, then stops and sets the EOC bit.
Channel Scan, Continuous Conversion Mode
22.2
The software controls the A/D Converter and reads the A/D
results by accessing the ADC registers. There are eight such
registers:
— ADC Status Register (ADCST)
— ADC Control 1 Register (ADCCNT1)
— ADC Control 2 Register (ADCCNT2)
— ADC Control 3 Register (ADCCNT3)
— ADC Data Registers (ADDATA0 through ADDATA3)
A/D CONVERTER REGISTERS
22.2.1
The ADCST register is a byte-wide register that indicates the
current status of the A/D Converter. One bit in this register,
the OVF flag bit, is cleared by writing a 1 to its bit position.
The other bits are read-only bits, so the values written to
them are ignored. Upon reset, the register is set to 30 hex.
The register format is shown below.
7
6
5
4
3
Reserved
BUFPTR
Reserved
ADC Status Register (ADCST)
EOC
End of Conversion. This read-only bit reports
the status of the most recent A/D Converter op-
eration. When cleared to 0, it indicates that the
conversion is not complete. When set to 1, it in-
dicates that the conversion is complete. The
hardware sets this bit when it places the con-
version results in the buffer and clears it when
any of the data registers are read.
ADC Busy. This read-only bit is set to 1 when
the A/D Converter is busy converting data and
is cleared to 0 when the A/D Converter is idle
or disabled.
Overflow. The hardware sets this bit to 1 when
the A/D Converter finishes a conversion and at-
tempts to store the results in one of the data
registers (ADDATA0-ADDATA3) while the reg-
ister is full. When this happens, the A/D Con-
verter overwrites the data in the data register,
sets the OVF flag, and continues operating.
The OVF flag remains set until cleared by the
software. The software clears the flag by writ-
ing a 1 to it. Writing a 0 to this bit has no effect.
Buffer Pointer. This 2-bit, read-only field identi-
fies the data register that was most recently
written with new data:
00 = ADDATA0
01 = ADDATA1
10 = ADDATA2
11 = ADDATA3
BUSY
OVF
BUFPTR
Figure 74.
A/D Converter Block Diagram
12:1
ANALOG
MUX
SAMPLE
&
HOLD
CONFIGURATION
STATUS
&
CONTROL
DATA
BUFFER
CLOCK
DIVIDER
PERIPHERAL
BUS
CLK
CLK
V
REF
CH0
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
ANALOG
TO
DIGITAL
CONVERTER
4
2
1
0
OVF
BUSY
EOC
相關PDF資料
PDF描述
CR16MCS9VJE8Y Microcontroller
CR16MCT5VJE7Y Microcontroller
CR16HCS5VJE8 Microcontroller
CR16HCS9VJE7Y Microcontroller
CR16HCS9VJE8Y Microcontroller
相關代理商/技術參數
參數描述
CR16MCS9VJE8/NOPB 功能描述:16位微控制器 - MCU RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
CR16MCS9VJE80 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers
CR16MCS9VJE81 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers
CR16MCS9VJE82 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers
CR16MCS9VJE83 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*