- 您現在的位置：買賣IC網 > PDF目錄1909 > CS61584A-IQ3Z (Cirrus Logic Inc)IC LINE INTERFACE T1/E1 64LQFP PDF資料下載
參數資料
| 型號： | CS61584A-IQ3Z |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 10/47頁 |
| 文件大小： | 0K |
| 描述： | IC LINE INTERFACE T1/E1 64LQFP |
| 標準包裝： | 160 |
| 接口： | 并行/串行 |
| 電源電壓： | 3.3V，5V |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 托盤 |
| 安裝類型： | 表面貼裝 |
| 產品目錄頁面： | 759 (CN2011-ZH PDF) |
| 其它名稱： | 598-1713 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
CS61584A
18
DS261PP5
The transmitter impedance changes with the line
length options in order to match the load imped-
ance (75
for E1 coax, 100 for T1, 120 for
E1 shielded twisted pair), providing a minimum of
14 dB return loss for T1 and E1 frequencies during
the transmission of both marks and spaces. This
improves signal quality by minimizing reflections
from the transmitter. Impedance matching also re-
duces load power consumption by a factor of two
when compared to the return loss achieved by using
external resistors.
The CS61584A driver will automatically detect an
inactive TLCK (i.e., no data clocked to the driver)
or REFCLK input. When either of these conditions
are detected the driver is forced to the tristate (high-
impedance) condition. If the jitter attenuator is in
the transmit path, the driver will tristate after 170 to
182 TCLK clock cycles. If the attenuator is not in
the transmit path, the driver will tristate after 4 to
12 TCLK clock cycles. During Host mode opera-
tion, the CLKLOST bit in the Status register goes
high to indicate when the driver is tristated due to
the absence of TCLK or REFCLK. The driver exits
the tristate condition when four clock cycles are in-
put to TCLK. On power-up or reset, the driver is
tristated until REFCLK is present and four clock
cycles are input to TCLK. In Host mode the driver
will have to be taken out of the tristate condition by
writing the CON[3:0]. The driver is not forced to
the tristate condition during remote loopback if
TCLK is absent.
When the transmit configuration established by
CON[3:0], TAOS, or LLOOP changes state, the
transmitter stabilizes within 22 TCLK bit periods.
The transmitter takes longer to stabilize when
RLOOP1 or RLOOP2 is selected because the tim-
ing circuitry must adjust to the new frequency from
RCLK.
When the transmitter transformer secondaries are
shorted through a 0.5
resistor, the transmitter
will output a maximum of 50 mA-rms, as required
by the European specification BS6450. This spec is
met for 5.0 V operation only.
4. RECEIVER
The input signal is connected to the receiver
through a step down transformer (1.15:1 for 5 V
and 2:1 for 3.3 V). Data and clock are extracted
from the T1/E1 signal input to the line interface and
to the system. The signal is detected differentially
across the receive transformer and can be recov-
ered over the entire range of short haul cable
lengths. The transmit and receive transformer spec-
ifications are identical and are presented in the Ap-
plications section. As shown in Table 1, the
receiver slicing level is set at 65% for DS1/DSX-1
short-haul and at 50% for all other applications.
The clock recovery circuit is a second-order phase
locked loop that can tolerate up to 0.4 UI of jitter
from 10 kHz to 100 kHz without generating errors
(Figure 13). The clock and data recovery circuit is
tolerant of long strings of consecutive zeros and
will successfully recover a 1-in-175 jitter-free line
input signal.
Recovered data at RPOS and RNEG (or RDATA)
is stable and may be sampled using the recovered
clock RCLK. During Hardware mode operation,
10
1k
10k
1
100
100k
700
.1
1
10
100
.4
28
300
PEAK-TO-PEAK
JITTER
(unit intervals)
JITTER FREQUENCY (Hz)
CS61584A
Performance
138
AT&T 62411
(1990 Version)
Figure 16. Minimum Input Jitter Tolerance of Receiver
(Clock Recovery Circuit and jitter Attenuator)
CS61584A
18
DS261F1
相關PDF資料 |
PDF描述 |
|---|---|
| CS61884-IRZ | IC LN INTERF T1/E1/J1 160-LFBGA |
| CS8130-CS | IC IR TRANSCEIVER 2-5V 20-SSOP |
| CS8190EDWF20G | IC TACH/SPEEDO DRVR PREC 20SOICW |
| CS8191XNF16 | IC DRVR AIRCORE TACH/SPEED 16DIP |
| CS82C5296 | IC UART/BRG 5V 16MHZ 28-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS61584A-IQ3ZR | 功能描述:網絡控制器與處理器 IC IC 3.3V/5V Dul T1/E1 Line Intrfc Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| CS61584A-IQ5 | 功能描述:網絡控制器與處理器 IC IC 3.3V/5V Dual T1/ E1 Line Intrfc Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| CS61584A-IQ5Z | 功能描述:網絡控制器與處理器 IC IC 3.3V/5V Dual T1/ E1 Line Intrfc Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| CS61584A-IQ5ZR | 功能描述:網絡控制器與處理器 IC IC 3.3V/5V Dul T1/E1 Line Intrfc Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| CS61584-IL3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Line Interface |
發布緊急采購，3分鐘左右您將得到回復。