- 您現在的位置：買賣IC網 > PDF目錄376560 > DAC757IDGSR (Texas Instruments, Inc.) QUAD, 12-BIT, LOW-POWER, VOLTAGE OUTPUT, I2C INTERFACE DIGITAL-TO-ANALOG CONVERTER PDF資料下載
參數資料
| 型號： | DAC757IDGSR |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | QUAD, 12-BIT, LOW-POWER, VOLTAGE OUTPUT, I2C INTERFACE DIGITAL-TO-ANALOG CONVERTER |
| 中文描述： | 四，12位，低功耗，電壓輸出，I2C接口的數字模擬轉換器 |
| 文件頁數： | 27/31頁 |
| 文件大?。?/td> | 783K |
| 代理商： | DAC757IDGSR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁
www.ti.com
1
2
3
6
8
7
10
9
DAC7574
V
OUT
A
V
OUT
B
V
DD
GND
V
OUT
C
V
OUT
D
A1
A0
SDA
SCL
GPIO-2
GPIO-1
V
DD
Microcontroller or
Microprocessor
NOTE: DAC7574 power and input/output connections are omitted for clarity, except I C Inputs.
4
5
DAC7574
SLAS375–JUNE 2003
APPLICATION INFORMATION (continued)
Figure 41. Using GPIO With a Single DAC7574
Bit-banging I
2
C with GPIO pins can be done by setting the GPIO line to zero and toggling it between input and
output modes to apply the proper bus states. To drive the line low, the pin is set to output a zero; to let the line
go high, the pin is set to input. When the pin is set to input, the state of the pin can be read; if another device is
pulling the line low, this reads as a zero in the port’s input register.
Note that no pullup resistor is shown on the SCL line. In this simple case the resistor is not needed. The
microcontroller can simply leave the line on output, and set it to one or zero as appropriate. It can do this
because the DAC7574 never drives its clock line low. This technique can also be used with multiple devices, and
has the advantage of lower current consumption due to the absence of a resistive pullup.
If there are any devices on the bus that may drive their clock lines low, the above method should not be used.
The SCL line should be high-Z or zero, and a pullup resistor provided as usual. Note also that this cannot be
done on the SDA line in any case, because the DAC7574 drives the SDA line low from time to time, as all I
2
C
devices do.
Some microcontrollers have selectable strong pullup circuits built in to their GPIO ports. In some cases, these
can be switched on and used in place of an external pullup resistor. Weak pullups are also provided on some
microcontrollers, but usually these are too weak for I
2
C communication. Test any circuit before committing it to
production.
27
相關PDF資料 |
PDF描述 |
|---|---|
| DAC7611 | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
| DAC7611P | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
| DAC7611PB | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
| DAC7611U | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
| DAC7611UB | Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC-76 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| DAC7611 | 制造商:BB 制造商全稱:BB 功能描述:12-Bit Serial Input DIGITAL-TO-ANALOG CONVERTER |
| DAC7611P | 功能描述:數模轉換器- DAC 12-Bit Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC7611P | 制造商:BURR-BROWN 功能描述:IC 12BIT DAC 7611 DIP8 |
| DAC7611PB | 功能描述:數模轉換器- DAC 12-Bit Serial Input RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。