- 您現在的位置：買賣IC網 > PDF目錄1912 > DLP-HS-FPGA3 (DLP Design Inc)MODULE USB-TO-FPGA SPARTAN 3A PDF資料下載
參數資料
| 型號： | DLP-HS-FPGA3 |
| 廠商： | DLP Design Inc |
| 文件頁數： | 17/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | MODULE USB-TO-FPGA SPARTAN 3A |
| 標準包裝： | 1 |
| 系列： | FPGA |
| 模塊/板類型： | FPGA 模塊 |
| 適用于相關產品： | USB |
| 其它名稱： | 813-1036 |
Rev. 1.1 (April 2012)
8
DLP Design, Inc.
11.0 USING THE DLP-HS-FPGA3
Select a power source via Header Pins 23 and 24, and connect the DLP-HS-FPGA3 to the PC to
initiate loading of the USB drivers. The easiest way to do this is to connect Pins 23 and 24 to each
other. This will result in operational power being taken from the host PC. Once the drivers are loaded,
the DLP-HS-FPGA3 is ready for use.
Simply connect the DLP-HS-FPGA3 to the PC to initiate the loading of USB drivers.
You can either utilize the Test Application available from http://www.dlpdesign.com/test.shtml with
the DLP-HS-FPGA3 (as described in Section 12), or you can write your own program in your
language of choice.
If you are using the VCP drivers, begin by opening the COM port, and send multi-byte commands as
shown in Table 1 below. There is no need to set the baud rate because the DLP-HS-FPGA3 uses a
parallel interface between the USB IC and the FPGA. (The Ping Command can be used to locate the
correct COM port used for communicating with the DLP-HS-FPGA3, or you can look in Device
Manager to see which port was assigned by Windows.) If you are using the D2XX drivers as with the
Test Application, no COM port selection is necessary.
TABLE 1
相關PDF資料 |
PDF描述 |
|---|---|
| DP83848CVVX/NOPB | TXRX ETHERNET PHYTER 48LQFP |
| DP83848HSQ/NOPB | IC TXRX ETHERNET PHYTER 40-LLP |
| DP83848YB/NOPB | IC TXRX ETHERNET PHYTERA 48-LQFP |
| DRM4000-N00-232 | DRM 4000 MODULE |
| DRM4000L-N00-232 | MODULE DEAD RECKONING RS-232 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DLP-HS-FPGA-A | 功能描述:FPGA Embedded Module Spartan-3A, XC3S200A FT2232H 66MHz 32MB 制造商:dlp design inc. 系列:FPGA 零件狀態:有效 模塊/板類型:FPGA，USB ?? 核心處理器:Spartan-3A，XC3S200A 協處理器:FT2232H 速度:66MHz 閃存大小:- RAM 容量:32Mb 連接器類型:USB - B，引腳接頭 大小/尺寸:3" x 1.2"（76.2mm x 30.5mm） 工作溫度:0°C ~ 70°C 標準包裝:1 |
| DLP-IO14 | 功能描述:數據記錄與采集 14-Channel Data-Acq Module RoHS:否 制造商:Lantronix 描述/功能:Analog device server 顯示器類型:None 電流額定值: |
| DLP-IO16 | 功能描述:界面模塊 USB/Micro Dev Board RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| DLP-IO20 | 功能描述:數據記錄與采集 USB-BASED 20-CHANNEL DATA ACQUISITION MOD RoHS:否 制造商:Lantronix 描述/功能:Analog device server 顯示器類型:None 電流額定值: |
| DLP-IO26 | 功能描述:開發板和工具包 - PIC / DSPIC USB/Micro Dev Board RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。