- 您現在的位置：買賣IC網 > PDF目錄1913 > DS1876T+T&R (Maxim Integrated Products)IC CTRLR SFP DUAL LDD 28TQFN PDF資料下載
參數資料
| 型號： | DS1876T+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/69頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTRLR SFP DUAL LDD 28TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | SFP 激光控制器 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | I²C |
| 電流 - 電源： | 10mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
19
Maxim Integrated
SFP Controller with Dual LDD Interface
DS1876
Transmit Fault (TXFOUT) Output
TXFOUT can be triggered by all alarms, warnings, QTs,
TXD1, TXD2, TXF1, and TXF2 (see Figure 9). The six
ADC alarms and warnings are controlled by enable bits
(Table 01h/05h, Registers F8h and FCh). See Figures
11a and 11b for nonlatched and latched operation for
TXFOUT. The CNFGB register (Table 02h, Register 89h)
controls the latching of the alarms.
Die Identification
The DS1876 has an ID hardcoded in its memory. Two
registers (Table 02h, Registers 86h
-87h) are assigned
for this feature. Register 86h reads 76h to identify the
part as the DS1876; Register 87h reads the present
device version.
I2C Communication
I2C Definitions
The following terminology is commonly used to describe
I2C data transfers.
Master Device: The master device controls the slave
devices on the bus. The master device generates SCL
clock pulses and START and STOP conditions.
Slave Devices: Slave devices send and receive data
at the master’s request.
Bus Idle or Not Busy: Time between STOP and
START conditions when both SDA and SCL are inac-
tive and in their logic-high states.
START Condition: A START condition is generated
by the master to initiate a new data transfer with a
slave. Transitioning SDA from high to low while SCL
remains high generates a START condition. See
Figure 12 for applicable timing.
STOP Condition: A STOP condition is generated
by the master to end a data transfer with a slave.
Transitioning SDA from low to high while SCL remains
high generates a STOP condition. See Figure 12 for
applicable timing.
Repeated START Condition: The master can use
a repeated START condition at the end of one data
transfer to indicate that it will immediately initiate a
new data transfer following the current one. Repeated
STARTs are commonly used during read operations
to identify a specific memory address to begin a data
transfer. A repeated START condition is issued identi-
cally to a normal START condition. See Figure 12 for
applicable timing.
Bit Write: Transitions of SDA must occur during the
low state of SCL. The data on SDA must remain valid
and unchanged during the entire high pulse of SCL
plus the setup and hold time requirements (Figure 12).
Data is shifted into the device during the rising edge
of the SCL.
Bit Read: At the end of a write operation, the master
must release the SDA bus line for the proper amount
of setup time (Figure 12) before the next rising edge
Figure 11a. TXFOUT Nonlatched Operation
Figure 11b. TXFOUT Latched Operation
DETECTION OF TXFOUT FAULT
TXFOUT
DETECTION OF TXFOUT FAULT
TXD_ OR TXFOUT RESET
TXFOUT
相關PDF資料 |
PDF描述 |
|---|---|
| DS1877T+T&R | IC CTLR/MON SFP 1-2CH 28TQFN |
| DS1878T+T&R | IC CTLR SFP W/DGTL LDD RX 28TQFN |
| DS1881Z-050+T&R | IC DGTL POT NV 2CH 45K 16-SOIC |
| DS1882Z-050+T&R | IC POT DIGIT DL LOG 50K 16SOIC |
| DS1884AT+T | IC SFP PON ONU CTRLR 24TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1877 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SFP Controller for Dual Rx Interface |
| DS1877T+ | 功能描述:ADC / DAC多通道 SFP+ Controller w/ Dual RX Interface RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| DS1877T+T&R | 制造商:Maxim Integrated Products 功能描述:SFP CTRLR FOR DUAL RX INTERFACE TQF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CTLR/MON SFP 1-2CH 28TQFN |
| DS1877T+T&R | 功能描述:ADC / DAC多通道 SFP+ Controller w/ Dual RX Interface RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| DS1877T+TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SFP Controller for Dual Rx Interface |
發布緊急采購，3分鐘左右您將得到回復。