參數資料
型號： DS21448DK
廠商： Maxim Integrated Products
文件頁數： 28/60頁
文件大小： 0K
描述： KIT DESIGN LIU DS21448 T1/J1/E1
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
主要目的： 電信，線路接口單元（LIU）
已用 IC / 零件： DS21448
已供物品： 板，子卡，CD
DS21448 3.3V T1/E1/J1 Quad Line Interface
34 of 60
10Hz to 100kHz) is added to the jitter present on TCLK. Also, the waveforms created are independent of the duty
cycle of TCLK. The transmitter couples to the E1 or T1 transmit-twisted pair (or coaxial cable in some E1
applications) through a 1:2 step-up transformer. For the device to create the proper waveforms, the transformer
used must meet the specifications listed in Table 7-C.
The DS21448 has an automatic short-circuit limiter that limits the source current to 50mA (RMS) into a 1 load.
This feature can be disabled by setting the SCLD bit (CCR2.5) = 1. When the current limiter is activated, TCLE
(SR.2) is set even if the short-circuit limiter is disabled. The TPD bit (CCR4.0) powers down the transmit-line driver
and tri-states the TTIP and TRING pins. The DS21448 can also detect when the TTIP or TRING outputs are open
circuited. When an open circuit is detected, TOCD (SR.1) is set.
7.3 Jitter Attenuator
The DS21448 contains an on-board jitter attenuator that can be set to a depth of either 32 or 128 bits through the
JABDS bit (CCR4.2). The 128-bit mode is used in applications where large excursions of wander are expected.
The 32-bit mode is used in delay-sensitive applications. Figure 7-8 shows the attenuation characteristics. The jitter
attenuator can be placed in either the receive path or the transmit path by appropriately setting or clearing the JAS
bit (CCR4.3). Also, setting the DJA bit (CCR4.1) can disable the jitter attenuator (in effect, remove it). For the jitter
attenuator to operate properly, a 2.048MHz or 1.544MHz clock must be applied at MCLK. ITU specification G.703
requires ±50ppm accuracy for T1 and E1. TR62411 and ANSI specs require ±32ppm accuracy for T1 interfaces.
An on-board PLL for the jitter attenuator converts the 2.048MHz clock to a 1.544MHz rate for T1 applications.
Setting JAMUX (CCR1.3) to logic 0 bypasses this PLL. On-board circuitry adjusts either the recovered clock from
the clock/data recovery block or the clock applied at the TCLK pin to create a smooth jitter-free clock, which is used
to clock data out of the jitter attenuator FIFO. It is acceptable to provide a gapped/bursty clock at the TCLK pin if
the jitter attenuator is placed on the transmit side. If the incoming jitter exceeds either 120UIP-P (buffer depth is 128
bits) or 28UIP-P (buffer depth is 32 bits), the DS21448 divides the internal nominal 32.768MHz (E1) or 24.704MHz
(T1) clock by either 15 or 17 instead of the normal 16 to keep the buffer from overflowing. When the device divides
by either 15 or 17, it also sets the JALT bit in the receive information register 1 (RIR1).
7.4 G.703 Synchronization Signal
The DS21448 can receive a 2.048MHz square-wave synchronization clock, as specified in Section 10 of ITU
G.703. To use the DS21448 in this mode, set the receive-synchronization-clock enable (CCR5.3) = 1. The
DS21448 can also transmit the 2.048MHz square-wave synchronization clock, as specified in Section 10 of G.703.
To transmit the 2.048MHz clock, set the transmit-synchronization-clock enable (CCR5.2) = 1.
Table 7-A. Line Build-Out Select for E1 in Register CCR4 (ETS = 0)
L2
L1
L0
APPLICATION
N
RETURN LOSS
Rt ()
0
75
normal
1:2
N.M.
0
1
120
normal
1:2
N.M.
0
1
0
75
with high return loss
1:2
21dB
6.2
1
0
1
120
with high return loss
1:2
21dB
11.6
Table 7-B. Line Build-Out Select for T1 in Register CCR4 (ETS = 1)
L2
L1
L0
APPLICATION
N
RETURN LOSS
Rt ()
0
DSX-1 (0 to 133ft)/0dB CSU
1:2
N.M.
0
1
DSX-1 (133 to 266f)
1:2
N.M.
0
1
0
DSX-1 (266 to 399ft)
1:2
N.M.
0
1
DSX-1 (399 to 533ft)
1:2
N.M.
0
1
0
DSX-1 (533 to 655ft)
1:2
N.M.
0
1
0
1
-7.5dB CSU
1:2
N.M.
0
1
0
-15dB CSU
1:2
N.M.
0
1
-22.5dB CSU
1:2
N.M.
0
N.M. = Not meaningful.
相關PDF資料
PDF描述
382LX223M050A052 CAP ALUM 22000UF 50V 20% SNAP
RBC28DCMN CONN EDGECARD 56POS .100 WW
GBM24DCAD CONN EDGECARD 48POS R/A .156 SLD
RP08-2415DAW CONV DC/DC 8W 9-36VIN +/-15VOUT
VI-J5M-EZ-F3 CONVERTER MOD DC/DC 10V 25W
相關代理商/技術參數
參數描述
DS21448G+ 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21448GN+ 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21448L 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21448L+ 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21448L+W 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*