參數資料
型號： DS21448DK
廠商： Maxim Integrated Products
文件頁數： 4/60頁
文件大小： 0K
描述： KIT DESIGN LIU DS21448 T1/J1/E1
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
主要目的： 電信，線路接口單元（LIU）
已用 IC / 零件： DS21448
已供物品： 板，子卡，CD
DS21448 3.3V T1/E1/J1 Quad Line Interface
12 of 60
PIN
I/O
FUNCTION
CES
I
Receive and Transmit Clock Select. Selects which RCLK edge to update RPOS and RNEG and
which TCLK edge to sample TPOS and TNEG. CES combines TCES and RCES.
0 = update RPOS/RNEG on rising edge of RCLK; sample TPOS/TNEG on falling edge of TCLK
1 = update RPOS/RNEG on falling edge of RCLK; sample TPOS/TNEG on rising edge of TCLK
TPD
I
Transmit Power-Down
0 = normal transmitter operation
1 = powers down the transmitter and tri-states TTIP and TRING pins
TX0/TX1
I
Transmit Data Source Select Bits 0 and 1. These inputs determine the source of the transmit
LOOP0/LOOP1
I
Loopback Select Bits 0 and 1. These inputs determine the active loopback mode (Table 4-A).
MM0/MM1
I
Monitor Mode Select Bits 0 and 1. These inputs determine if the receive equalizer is in a monitor
RT1/RT0
I
Receive LIU Termination Select Bits 0 and 1. These inputs determine the receive termination
TEST
I
Tri-State Control. Set high to tri-state all outputs and I/O pins (including the parallel control port).
Set low for normal operation. Useful in board-level testing.
HRST
I
Hardware Reset. Bringing
HRST low resets the DS21448, setting all control bits to the all-zero
default state.
MCLK
I
Master Clock. A 2.048MHz (±50ppm) clock source with TTL levels is applied at this pin. This
clock is used internally for both clock/data recovery and for jitter attenuation. A T1 1.544MHz
clock source is optional (Note 1). See Table 4-F for details.
BIS0/BIS1
I
Bus Interface Select Bit 0 and 1. Used to select bus interface option (Table 2-A).
EGL1–EGL4
I
Receive Equalizer Gain-Limit Select. These bits control the sensitivity of the receive equalizers
PBEO1–PBEO4
O
PRBS Bit-Error Output. The receiver constantly searches for a 2
15 - 1 PRBS (ETS = 0) or a
QRSS PRBS (ETS = 1). The pattern is chosen automatically by the value of the ETS pin. It
remains high if it is out of synchronization with the PRBS pattern. It goes low when synchronized
to the PRBS pattern. Any errors in the received pattern after synchronization cause a positive-
going pulse (with same period as E1 or T1 clock) synchronous with RCLK.
RCL1–RCL4
O
Receive Carrier Loss. An output that toggles high during a receive carrier loss.
RTIP1–RTIP4
I
RRING1–RRING4
I
Receive Tip and Ring. Analog inputs for clock recovery circuitry. These pins connect through a
1:1 transformer to the line. See Section 7 for details.
BPCLK1–BPCLK4
O
Backplane Clock. A 16.384MHz clock output that is referenced to RCLK.
TTIP1–TTIP4
TRING1–TRING4
O
Transmit Tip and Ring. Analog line-driver outputs. These pins connect through a step-up
transformer to the line. See Section 7 for details.
RPOS1–RPOS4
O
Receive Positive Data. Updated on the rising edge (CES = 0) or the falling edge (CES = 1) of
RCLK with bipolar data out of the line interface. In NRZ mode (NRZE = 1), data is output on
RPOS, and a received error (BPV, CV, or EXZ) causes a positive-going pulse synchronous with
RCLK at RNEG.
RNEG1–RNEG4
O
Receive Negative Data. Updated on the rising edge (CES = 0) or the falling edge (CES = 1) of
RCLK with bipolar data out of the line interface. In NRZ mode (NRZE = 1), data is output on
RPOS, and a received error (BPV, CV, or EXZ) causes a positive-going pulse synchronous with
RCLK at RNEG.
RCLK1–RCLK4
O
Receive Clock. Buffered recovered clock from the line. Synchronous to MCLK in absence of
signal at RTIP and RRING.
TPOS1–TPOS4
I
Transmit Positive Data. Sampled on the falling edge (CES = 0) or the rising edge (CES = 1) of
TCLK for data to be transmitted out onto the line.
TNEG1–TNEG4
I
Transmit Negative Data. Sampled on the falling edge (CES = 0) or the rising edge (CES = 1) of
TCLK for data to be transmitted out onto the line.
TCLK1–TCLK4
I
Transmit Clock. A 2.048MHz or 1.544MHz primary clock used to clock data through the transmit
side formatter. It can be sourced internally by MCLK or RCLK. See Common Control Register 1
JTRST
I
JTAG Reset
JTMS
I
JTAG Mode Select
JTCLK
I
JTAG Clock
JTDI
I
JTAG Data In
JTDO
O
JTAG Data Out
VSM
I
Voltage Supply Mode (LQFP only). VSM should be wired low for correct operation.
TVDD1–TVDD4
–
3.3V, ±5% Transmitter Positive Supply
VDD1–VDD4
—
3.3V, ±5% Positive Supply
相關PDF資料
PDF描述
382LX223M050A052 CAP ALUM 22000UF 50V 20% SNAP
RBC28DCMN CONN EDGECARD 56POS .100 WW
GBM24DCAD CONN EDGECARD 48POS R/A .156 SLD
RP08-2415DAW CONV DC/DC 8W 9-36VIN +/-15VOUT
VI-J5M-EZ-F3 CONVERTER MOD DC/DC 10V 25W
相關代理商/技術參數
參數描述
DS21448G+ 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21448GN+ 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21448L 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21448L+ 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21448L+W 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*