參數資料
型號： DS21FF44
廠商： Maxim Integrated Products
文件頁數： 36/117頁
文件大?。?/td> 0K
描述： IC FRAMER E1 4X4 16CH 300-BGA
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 40
控制器類型： E1 調幀器
接口： 并行/串行
電源電壓： 2.97 V ~ 3.63 V
電流 - 電源： 300mA
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 300-BBGA
供應商設備封裝： 300-PBGA（27x27）
包裝： 管件
DS21FT44/DS21FF44
25 of 117
Signal Name:
RD* (DS*)
Signal Description:
Read Input (Data Strobe)
Signal Type:
Input
RD* and DS* are active-low signals. Note: DS is active high when MUX = 1. See bus timing diagrams in
Section 23.
Signal Name:
FS0 and FS1
Signal Description:
Framer Selects
Signal Type:
Input
Selects which of the four framers to be accessed.
Signal Name:
CS*
Signal Description:
Chip Select
Signal Type:
Input
Must be low to read or write to the device. CS* is an active low signal.
Signal Name:
WR* (R/W*)
Signal Description:
Write Input (Read/Write)
Signal Type:
Input
WR* is an active-low signal.
TEST ACCESS PORT PINS
Signal Name:
Test
Signal Description:
3–State Control
Signal Type:
Input
Set high to tri-state all output and I/O pins (including the parallel control port). Set low for normal
operation. Useful in board level testing.
Signal Name:
JTRST*
Signal Description:
IEEE 1149.1 Test Reset
Signal Type:
Input
This signal is used to asynchronously reset the test access port controller. At power-up, JTRST* must be
set low and then high. This action sets the device into the boundary scan bypass mode allowing normal
device operation. If boundary scan is not used, this pin should be held low. This function is available
when FMS = 0. FMS is connected to ground for the DS21FF44/DS21FT44.
Signal Name:
JTMS
Signal Description:
IEEE 1149.1 Test Mode Select
Signal Type:
Input
This pin is sampled on the rising edge of JTCLK and is used to place the test port into the various defined
IEEE 1149.1 states. If not used, this pin should be pulled high. This function is available when FMS = 0.
FMS is connected to ground for the DS21FF44/DS21FT44.
Signal Name:
JTCLK
Signal Description:
IEEE 1149.1 Test Clock Signal
Signal Type:
Input
This signal is used to shift data into JTDI on the rising edge and out of JTDO on the falling edge. If not
used, this pin should be connected to VSS. This function is available when FMS = 0.
相關PDF資料
PDF描述
DS21FT44N+ IC FRAMER 4X4 16CH 300-BGA
DS21Q352B IC TXRX QUAD T1/E1 3.3V 256-BGA
DS21Q41BT IC FRAMER T1 QUAD 128-TQFP
DS21Q42T+ IC FRAMER ENHANCED T1 4X 128TQFP
DS21Q43-ATN IC FRAMER E1 QUAD 5V 128-TQFP
相關代理商/技術參數
參數描述
DS21FF44N 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21FT40 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Four x Three 12 Channel E1 Framer
DS21FT40N 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
DS21FT42 功能描述:網絡控制器與處理器 IC 4x4 16/4x3 12 Chnl T1/T1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21FT42N 功能描述:網絡控制器與處理器 IC 4x4 16/4x3 12 Chnl T1/T1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*